Ok, ill try black unit.
The toner has some guarantee of good performance because it is a solvent manufacturer not whatever online bargain
I have no problem with others products so far.
Thanks.
Type: Posts; User: copycoan
Ok, ill try black unit.
The toner has some guarantee of good performance because it is a solvent manufacturer not whatever online bargain
I have no problem with others products so far.
Thanks.
Sorry,
This is not OEM toner but works fine in same model in others clients,
machine has 40k print B/W 30k Colour.
I think units have not been replaced at all.
Hello,
i have an issue with a Konica Minolta c360, after the first 30-50 prints it begin printing wiht gray background, its necessary to wait several hours or the next day to avoid this, any ideas...
jam 4101, jam4111 ---> duplex clutches, there is two in the rear of the conveying unit, one at the top and one at the bottom each one gives one or the other jam code.
ok thanks will try
You can try firmware update with compact flash, if not try the update using the switch in the operation panel, there is some posts with de explanation.
I have done several gemini kits mods and not always getting good results, next time ill try springs also, thanks.
Look for service bulletins, part changed "CAM TONER SUPPLY" and other modifications, this may solve it... sometimes.
Also check hinges are not broken.
Quick Tip: reinsert toner, open and close...
try u004 if not you can replace eeprom with a blank one and u004 may work, if not can try format hd otherwise pwb or dimm etc...
In gmail accounts there is a security option you may need to activate -allow less secure apps to access your account- https://support.google.com/accounts/answer/6010255?hl=en
http://upx.nz/fM2xHh
from kyocera ftp repository
P: kyocera
Have u tried printerultility.exe, it is and executable file,does not require installation only you need the driver installed, and allows you to send prescribe commands and many other options and...
Same problem, just power off the machine, disconnect the wire of laser cleaning motor from engine, power on the machine and it works, while powered on reconnect the motor and still working fine. It...
there is a service bulletin about "the stretch level of the belts of the machine front and rear side may differ due to the strong spring pressure of the spring (No.2) to close the toner waste shutter...
Check op panel wires also, I remember two machines with that (not same model) one was a wire and the other was the main pwb.
It is a TA DC2445 aka TASKalfa 4500i.
im using kyo toner in one B/W TA, we have no TA dealer, by removing the rfid pwb and some fin, it would be interesting change toner area code ir order to have the toner level working fine but the two...
I have tried it and in TA (like Taskalfa B/N) and the kyo toner do not fit well and if u can put it inside the machine, it detects the kyo toner and prompt a message to change it.
same problem "adding toner" i tried drive unit, etc.. i changed a gear GEAR DLP Z31H (bulletin Measures against the Developer Drive Gear Shaft Twist), gears on dev unit dont rotate properly, check...
there is a bulletin about bad connection of 2nd wire (in the right of the machine) just check the connection. also check the cis in the DP that read the second face.
I have performed this procedure several times. it responds up until I go to put in the card. Memory light flashes and then stays on after about a minute to a minute and a half. Turn off...
i got the same problem in 2550ci , the waste was not going out of drum units and the clutch for put out the waste inside of the drum was broken. also there is a bulletin about a clutch that moves the...
Hello, i got a TASKalfa 3500i with the optional card authentication kit(B) installed and activated but with no card reader, i do not need this fuction at all, the machine works fine but there is a...
any tip for scan to mac from taskalfa 221 or km-2050?
thanks in advance.
go to service manual and look for sim 224