they are not printing heavy solids it is a medical aid company and it is only application forms that they are printing. dont think that they are giving toner away as we are delivering and putting the...
Type: Posts; User: drolfe@webmail.co.za
they are not printing heavy solids it is a medical aid company and it is only application forms that they are printing. dont think that they are giving toner away as we are delivering and putting the...
Hi there i am new to samsung actually my first day today have just left toshiba. I have a machine the 8640nd which is using to much toner has only done 58800 black copies and has gone through about 8...
the fuser error is also caused by fluctuation in voltage we have a big problem with that here as we have load shedding quite often and when the power comes back on it spikes then it gives the error...
I have attached the scrrenshot of the files for the firmware update if that helps any
if you have the T169SLGWW.02 firmware then you have the 4CCD which is wrong
the red dot is 3ccd firmware, can you make a print from the computer cause if you have updated the incorrect firmware it will make a print but wont make a copy. if so the only way to repair it is...
Are you 100% sure that you loaded the correct firmware as it sounds identical to when we had loaded the 4ccd instead of the 3ccd. We had to send the scanner boaed away to get reprogrammed with the...
switch of machine then boot up holding start and 6 then press 2 then you can go and reset all the maintenance counts it will show you which ones are over
I have just checked the loom there are no breaks in the wiring.
this machine is driving me mad just doesnt make sense i also did a duplex motor test as that motor also gets driven from the same...
i have done the part check and the motor runs. when you make a copy the motor runs its just those 3 clutches that dont work the dev unit doesnt turn and the reg roller
Just di the switch on holdin 24 abd i get
SN-5 SM Bus Soc DIM1 (no)
SN-9 PCI Configuration PCI-Bridge (no)
all the others are ok , what does this mean?
i have done the switch on holding 24 and done the dcon clear it is still doing the same jamming at reg rollers. id there no switch or something that controlls the 24 voltage to the clutches or dc con...
thanks for that if i dont hae the p-print can i still do the reset?
The jam code is 0107
hi there
when it jams it only has the jam code now that the error code has gone as i have manually poured enogh toner in dev unit. I did a part chk and held the reg clutch in my had to see if i can...
ok i manually poured toner in dev unit now it comes ready makes a copy and jams at reg rollers i am convinced that all 3 clutches are not working i am thinking its the engine control board. is there...
what i just did was vacume all the toner out the dev unit the went into instal toner now it just gives me a NG
they are reading the mail on a computer not on any of the phones. i will have to check what protocols they are using. all the papertrail wants is the attachment as that is the fax they dont want the...
yes the attachment is there but its blank, ive tried tiff pdf and still the same there is no limit on the size as well.
all the settings are the same on new machine as on old machine. its weird as...
the error we get after a while is E0020 0000 05. just want to know when i do the instal toner in test mode is the dev unit supposed to be turning?
Hi There
i have just set up scan to email on the new e257 everythong routes correctly but when their software fetches the email the attachment is blank. when i send to an email account that you open...
it jams when you make a copy by the alignment roller as that is also on a clutch from what i can see and after a while it gives the error code that shows the toner not going through as it is all...
hi there
we have an IR 4035 adv which the dev unit doesnt seem to be turning we normally work on toshiba so not so fimiliar with the canon. it looks like all those clutches are not activating (dev...
Try logging into machine then go to administration then maintenance there is a page export/clearlog.
Give that a try and see what it does
ok great just wanted to clear that up as they were saying it could be as the strap cable broke but i know the adf wouldnt cause blank copies. there is main charge and transfer charge the transfer...