Search:

The Drivers I've been using are 5.10.106.2 and list the following models under the configuration tab: 6550c, 6540c, 5540c, 4540c, 3540c, 3040c, 2540c and 2040c and they are the full featured drivers...

I have ran into this issue a few times on the 3540c models and it was driver related, I was using the current drivers from the toshiba.ca website v7.49.xxxx and had all kinds of problems with jobs...

E712 is one of the most common errors I see on these ADF, most common problems is someone removing staples and the pages sticking together or just poor originals in general, if you've seen it with...

The transfer bias is applied from the 2nd transfer facing roller inside the transfer belt not the black sponge roller, I've seen transfer issues using thick paper many times on the 3510c and...

Is it the facing roller inside the belt or the black 2nd transfer roller on the right door that is squealing? If it's the roller on the door making the noise under the front plastic bearing holder...

In the left door behind the solenoid gate there is a black guide that will get small burrs on it and cause E020 jams, sanding them off works for a while. That guide has been modified 6LH73778000...

It took me forever to find it as well, it's in the optical-drive-assy section - 6LH61445000

Toner yield is based on 6% coverage for the 4520c and 6530c so I would assume it will be the same for the 4540c/6550c

The white guide on the transfer belt assy that the cleaning blade assy clips into was modified June 2009, if your machines are older than that replace the guide with 6LJ03322000

the pre-load must be done from a bootable HDD, if this is your situation I'd recommend calling a trained service technician, sorry.

Sorry just going by the manual but did notice the difference now in the regions, I get my machines delivered set up so guess I should not have given you advice, I'd suspect they are using different...

Also make sure the firmware is installed on the stick correctly, you should see a 352_452 folder and a file called mentusb.o in the root dir on the stick, but I suspect your problem is that the...

I'm not farmiliar with the Kyoshiba model, does it have the same firmware/service modes as the Toshiba 6520c? If so any time there is a problem with drum surface potential sensor control, you must...

Have you noticed or found a fix for drums leaving background, replacing the drum fixes the problem but some are not even half way due?

Both those models use GD-1250 and GD-1260 (2nd line) fax boards, so should be ok.

This is what I'm worried about, these machines were designed to compete and lower costs so not even sure that the units would withstand a rebuild. I miss the days of brass inserts and machine threads...

That's weird does the machine have the correct IPC board installed, also check 08-1912 and make sure it's set properly for the finisher installed, other than that make sure FW is updated on the...

I have not seen them yet but others have some in their territory, I've heard they are ERU's but have heard that there are PM kits for the units as well.... Our "Team Leader" can't/won't really answer...

Finding 2 pages in the buffer roller is normal, buffer roller holds 2 sheets to give the stapler time to finish the last set before sending in the next set, check the finisher height and make sure...

I worked for a Canon dealer and after using Katun for many years, a new service manager started and he declared that we would be using only OEM toner and consumables and it was amazing how well the...

You could use EFMS (e-Bridge Fleet Management System) not sure why you would require it for 3 machines but contact any Toshiba dealer and they would be able to sell it to you.

Check the logs either in the machine or through Top Access there will be a error code that can further help troubleshooting this problem.

What errors are you getting when you try to scan to email?

I agree, unless the toner that is blowing off the pages feels gritty (dumped developer) you are looking at a fixing issue.

I'm not sure what your concern with what Gregg sent you is but I checked the SH and it does say 8MB for master hard disk data which is incorrect, the current FW I have v355 has 1,2,3,@ 32MB and 4 is...