Search:

Type: Posts; User: slot

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    29
    Views
    3,854

    Re: Yellow print on RICOH MPC 6503

    every time i have seen this it is the drum potential sensor just change it with another colour to check
  2. Replies
    7
    Views
    784

    Re: MFC-L8900C no power

    thanks for all the info
  3. Replies
    7
    Views
    784

    Re: MFC-L8900C no power

    we have now got the main board and i have looked in the manuale to fit it my question is do i need to do everything it states in the manuale ior are there any short cuts it seems a lot to do .
  4. Replies
    7
    Views
    784

    Re: MFC-L8900C no power

    Thanks for the heads up I will get a price for the main board
  5. Replies
    7
    Views
    784

    MFC-L8900C no power

    We have an 8900 that wont power up no led on screen we have replaced the low power supply unit as it was outputting 6.2v
    also tried plugging in with power button held down 3 times as in others...
  6. Replies
    3
    Views
    492

    Re: sr3270 not stacking sheets to staple

    It was attached to an IM C 2500 one of our engineers fixed it today it was caused by the drive gears at the front of the machine being a couple of teeth out which made one of the cams slightly lower...
  7. Replies
    3
    Views
    492

    sr3270 not stacking sheets to staple

    Good morning all

    we have a sr3270 back in our workshop that had the trailing edge fence replaced ( the guide that rotates to hold rear edge) now for some reason when
    you ask it to do a staple...
  8. Re: MP5054 - J060,020,019,001, random, despite paper exit unit replacement

    I have had a couple of 54s with jamming problems and its caused by the reg rollers on the transfer roller unit swelling up or coming loose on there shaft so they start to move around in there slots...
  9. Replies
    7
    Views
    1,871

    Re: savin MP C 307 doc feed phantom jam codes

    if the screws on the hinges are loose where it screws into the body f the df can cause all sorts of jams worth taking the df off machine and laying it on its back and checking them
  10. Thread: lexmark reset

    by slot
    Replies
    1
    Views
    937

    lexmark reset

    we have a small mfd tosh c338 that is a lexmark engine the problem we have is we cant get into user tools to reset the ip address as it has a password
    i have tried what we normally set as the...
  11. Replies
    7
    Views
    1,498

    new c257i error c9402

    Not sure if anyone can help I have set up a new c257i today and it all worked ok installed d/f etc and ran through our setup sheet all ok and ran some test sheets
    the last thing I did was upgrade...
  12. Thread: SC995-01

    by slot
    Replies
    10
    Views
    3,672

    Re: SC995-01

    Enter the machine serial number using SP5-811,you will need to enter SP via special mode and use the original nvram
  13. Replies
    11
    Views
    3,631

    c300i wont calibrate fiery

    I have a c300i in our workshop that when printing out the fiery calibration sheet prints it out to small so when placed on the glass it errors .
    the scanner wont even try to scan the original. the...
  14. Replies
    0
    Views
    2,502

    es388cs or lexmark printer password help

    I set a es388 up today I know it is the same as a Lexmark I followed the wizard to set it up and added a password when prompted twice.
    I then continued to set it up then I came to changing the...
  15. Replies
    5
    Views
    6,536

    Re: e3015ac with error C262

    thanks guys they were all removed when the df was fitted its being sent back to toshiba
  16. Replies
    5
    Views
    6,536

    e3015ac with error C262

    we have just unboxed an 3015 and removed all packing parts etc and on power up it errors c262 at the end of loading I have disconnected the DF and re seated the ccd cable on ccd and the main board ...
  17. Replies
    11
    Views
    5,296

    Re: MP C3503 - Can't print Multiple Sets with PCL6

    We always set up auto contiue to immediate and in printer sp change sp1-001-005 bit1 and auto nrotate continue to on.
  18. Replies
    9
    Views
    4,354

    [Error Code] Re: MP C401SP - SC670-00

    Not sure if this helps but on th MPC3003 you get a simulare fault due to the toner bottle try removing them and powering it up and see what you get.
  19. Replies
    13
    Views
    4,775

    [Misc] Re: IM C2500 silly question?

    This is some info from an old training book it may work on the new copiers
    Letterhead Setting
    1. UserTools, Printer Settings, System
    2. LetterheadSetting put on Auto Detect
    3. ...
  20. Replies
    11
    Views
    5,236

    Re: Calibrate print colour poor

    i have sent you a PM
  21. Replies
    14
    Views
    4,648

    [Misc] Re: MP 4002 network connectivity

    the first thing i do now with these calls is print out the configeratiobn page and see if is enabled customers are nightmares for this.
  22. Replies
    7
    Views
    3,324

    Re: Mpc305 auto paper select ?

    There are no paper size sen in the df so when you do an odd job you would need to select the original size on the left side of the screen not sure if this helps you out but its the smae on an MP301
  23. Replies
    3
    Views
    2,944

    Re: Pro c5100 sc204-03

    thanks for the reply they seem to be haveing power probs at the moment but the copier has started to work ok
  24. Replies
    3
    Views
    2,944

    Pro c5100 sc204-03

    Just putting this out there has anyone had sc204-03 on a pro c5100 type copier we have a call for one and it looks expensive can anyone give ay advice thanks
  25. Replies
    9
    Views
    7,924

    Re: pro8100 sc621 tcb full

    can you point me in direction of fuse as I have a another one with same fault I have checked I have 240v to the psu c but no 24 out thanks
    im about to order puc c this could save me some money
Results 1 to 25 of 339
Page 1 of 14 1 2 3 4