YES YES YES! 10.255.255.2 was the answer! I knew it was something like that, but could not remember the exact address.
I was able to log in and now I can control the screen from the RIP. So I...
Type: Posts; User: victoryprinting
YES YES YES! 10.255.255.2 was the answer! I knew it was something like that, but could not remember the exact address.
I was able to log in and now I can control the screen from the RIP. So I...
I did print out the config pages and went over every line prior to my post - it just showed the network info for the Q1. I searched a long time for the IP for the C1, but found nothing - both through...
I have an ImagePress C1 that occasionally had some touch screen issues many years back, and I used the Canon Remote Operation Viewer so I could get an image of the touch screen on my Q1 RIP screen...
Mystery is solved. Upon checking the jam code log in service mode (thanks, Ron), I could see that PS15 was the sensor that was sending the jam signal upon startup.
PS15 is in the fixing unit. The...
I have an ImagePress C1, and upon startup, I get a paper jam warning in the reverse paper path area just past the fixing unit. Previously, I could get past it when I pulled out the drawer, opened...
Thanks for the suggestions. It seems to have resolved itself, so I won't rip it's guts out unless I see another registration issue!
I got another pesky 020 code, which I quickly resolved by replacing the Magenta developer, as the spatter shield was disintegrating and a piece got pulled into the developer unit. It...
I did replace the sub hopper unit and blew out the supply tube below the sub hopper unit, but it did not eliminate the problem with the black dropping out. I speculated that it could have...
This code came up on my C1. Months ago, I noticed that the black was printing light for about 4 copies when it pulled the same error code. At that time, the black toner was depleted but an "out of...
I am wondering if there is an adjustment that can be made when running single sided LTR stock. It appears that it places 2 images on the transfer belt and 2 sheets of LTR are run through in one...
Going back last year to my original post, I did not have the web length detector arm set properly. I put the cleaning web BETWEEN the "feelers", but it should have been placed so BOTH feelers were...
Success! Here's what I did, in case someone encounters this or similar issues down the road:
I noticed the Cyan developer unit was depositing toner on the ATR shutter as I rotated the developer...
I just installed a 2nd ImagePress C1 (I know, I'm a glutton for punishment - but this model prints so beautifully!)
I was getting an 020 code on the yellow, and since that developer unit was an...
I don't have any test sheets. Would it suffice to output them from my computer using a standard Blue, Green, Red & Black?
So to confirm, you run them all 11x17 single sided with the 20 copies of...
The only step in the process to replace the start developer that I am unclear about is this:
17) Execute aging in the following order.
- Execute 20 sheets of duplexing print for Blue solid color...
Another code is now coming up on my ImagePress C1.
E020-01a8. "The T/D ratio identified at ATR control has exceeded the upper limit (14%) 3 times continuously. Turn off and on main power." I...
Back up and running! I replaced the board from my spare parts copier. I appreciate your knowledge and prompt responses to the site. I just made an additional donation to Copytechnet.com to help...
I pulled a spare backside driver PCB and will install it on my C1. It does not have fuses on it. Are there fuses somewhere else I should check? I am also having a hard time locating the plug you...
Quick question: When you reference the lower left hand side, which side are you facing? I took the back panels off, but perhaps it is on the feed end of the copier? I could not find a location...
Here is what I found for the code:
E021-0001. The developing rotary HP failed to be detected.
There is a fault in the developing rotary HP sensor or the wiring of the DC controller PCB. Or the...
Thank you so much for that helpful PDF. That is exactly what I am experiencing.
Just two more question before I dive into the C1.
1. Would the drum be damaged to the point of needing to be...
They are all at zero.
But the strange thing is: when I started the C1 up the next day, the colors were amazingly brilliant - just like before I had the problem. Same settings, same file from the...
What might cause just the black to be printing light on an Imagepress C1? I have some spare process units which I have swapped out, but they have no change in the lightness.
I had some heavy...
When I replaced the web, I also looked under COPIER > COUNTER > MISC and there was no FIX-WEB option listed. I figured that was the issue, but it is just not there.
I have a C1 and my web cleaning roller ran out, so I replaced it with a partial roll that I had acquired with a bunch of parts. The web is properly threaded between the plastic detector feelers, and...