I'm looking for a KM-4050 vertical feed unit, please contact me if you have one.
Type: Posts; User: jockey
I'm looking for a KM-4050 vertical feed unit, please contact me if you have one.
UPDATE!
Went back today and noticed a clunk noise, pulled the left door off and cheated the interlock so I could watch what was going on, put the machine in simm and ran the paper feed motor, put my...
Thanks for the input guys, I'm going back tomorrow will post a update on what I find.
I went on a call yesterday and found the middle feed unit (302GR93150) had broken where the clutch mounts to the plastic, I replaced the unit and now the machine will run 20 to 40 copies then make a...
I have a 300ci throwing the same code, took the back off turned on the power switch all the motors turn, could it still be one of the motors? I noticed Texchar555 said the motor was "going out"
Update!... It was the paper lift motor, must have had a intermittent problem, the drawer would lift and would feed a few sheets of paper before throwing the error. thanks for the help!
Ok darry will give that a shot, going to look and see if it's the same lift motor as in the 4050/5050 if so will test with one of those
Went on a call yesterday the customer said it won't print, computer said printer offline, went to the copier and it says ( tray 1 error, remove paper from tray 1) there's no jam. I swapped the feed...
I just had this same problem yesterday, It would say "program loading" continuously, I replaced the hard drive and that took care of the problem.
Thanks guys, it turned out to be the exit sensor.
I have a SCX 6345 that will run a job fine then jam everytime on the next, I'm a Kyocera guy and have never worked on Samsung, I replaced the feed tires in both trays hopeing that was the cause, the...
I have a 3500i that has been printing fine, now it's throwing a PCL XL error and Input read error, I have changed the PDL setting but it's still giving me the error. Anyone have ideas on this code?
Were past what will print and what won't, It does print that's no longer the issue, the XPrintServer did the job, problem is the font size is to small and it's not just the KM machine the HP printer...
Yes I know exactly how old this copier is it has print, scan, and fax installed and it's on the list of printers the XPrintServer will print to, this customer has a new HP printer along with the...
UPDATE: I installed the XPrintServer today and there able to print from Ipad & Iphone but the fonts are so small there almost unreadable, I have been reading several forums discussing this font size...
Hey guys thanks for all your suggestions! the printopia looked promising but found out it has to be loaded on a Mac first so that won't work, looks like the xPrintServer is the way to go. Thanks...
Kyocera print does not support the KM-2530, printopia looks promising!
I have a customer trying to print from a Ipad to a old KM-2530 is there a app for this?
Well add me to that list! that's what it was went back this morning and found the scanner lock was half way in. Thanks guys
I have a CS 205c that had the "Black Image problem" that has been addressed in one of the tech bulletins and called for the main board to be replaced. The original problem was black image when making...
Tried the U600 and firmware, It will not allow you to run U600 becuase it does not reconize the Fax card in the machine.
I have a 255 that just beeps when you press the fax button it never goes to the fax screen, installed a new fax card and it does the same thing, any ideas? I'm thinking it's a main board issue.
Haven't tried it yet, this machine is 100 miles away will give it a try next week.
I have a issue simular to this on a 5050, it says "excuting TX job" at the bottom of the screen, if you check job status to cancel the job there's no job showing, I tried another fax card and got...
Thanks Blackcat, guess I need to order C,Y,M dev units