The problem is that the DP open close switch located on the DP is stuck on as though the Document processor is always closed. Nothing to do with the switch on the top of the copier or anything under...
Type: Posts; User: nathicana
The problem is that the DP open close switch located on the DP is stuck on as though the Document processor is always closed. Nothing to do with the switch on the top of the copier or anything under...
Try a different glass if you have one. That's assuming you have already cleaned the underside of the glass. There was a smaller machine that would give a lamp code due to the glass being grimy but it...
Thanks KYO_OEM, I adjusted exit motor speed to -3500 in u053 motor 3 as shown above.
The 11 x 17 jamming problem seems to be resolved.
Could this adjustment also help cure 500x non arrival...
Any definite solution to this AK-7110 jamming problem on 11 x 17?
I'm getting j4918, j4912 bridge conveying sensor 1 stay jam only on 11 x 17 with paper stalled about to exit AK-7110
I'm...
Belt cleaning motor is suspect for C2840 not waste toner motor. It is located on the transfer belt assembly.
61515
There is another bulletin H243 that explains a torn off seal that gets caught...
If you want to disable sleep mode you should be able to do it utilizing maintenance mode u346.
See this page from the service manual
setting: auto sleep on or off
59921
The idea that someone copies or scans their social security card and it remains stored on a hard drive is likely a myth.
It would be interesting to look at the actual files that reside on a copier...
Thanks for the reply. Looking on KFS it says: Color selection (Copy) : Black & White. They may be selecting auto color for this type of job, I will check on that.
I agree with the idea that copy...
58090
Sandy Scheuer was on her way to class on May 4, 1970, when she was shot and killed by Ohio National Guardsmen responding to protests of the Vietnam War at Kent State University. She was a...
We have a customer that traded in a 3553ci with a DP-7110 for a 3554ci with a DP-7160.
They are noticing that when they are copying colored legal size originals in color the document feeder runs...
There is a multi feed being detected for the 051x jams. I see this even on new machines so it isn't always the feed tires being worn out.
If it's the paper then these machines are way too...
I agree with the above comments that the waste toner container is probably not rotating.
There is a magic way to get the WTB shell to pop back into place so it will turn again. Lift the paper...
I've found Internet Explorer is difficult to use because it is so outdated.
Here's an open source browser that supports TLS 1 so you can easily get into the older machines to turn on TLS 2 and...
In what section of the service manual is this table?
The training center stepped in and fixed my record as well. Today I noticed that the training requirements have been clarified to say:
Technicians currently certified on the previous online series...
Has anyone taken the Kyocera training for the PA6000 series printers?
When I finish the test for part 2 it says "congratulations you passed" or something like that.
Then I click on the check...
We have a 5003 with a DF-7100 inner finisher saying "inner tray full" even when there is no paper present. Problem is intermittent. We have tried replacing the exit unit. I think it is something to...
Check the alarms (copier-display-alarm2) and look them up in the service manual.
Run a series of pg5 pages of each individual color and look for deletions. There needs to be a full page solid...
Where did you find the repetitive defects guide? I looked in the service manual and troubleshooting guide, must have missed it.
We replaced a white one way gear FL3-5201-000 for jamming from the left deck. The second side of duplexing also depends on this gear. Jams 0110, 020c, 010D
Could someone have loaded paper into the machine that has these marks already on it?
Can anyone verify if these jams have occurred on a machine without a speed license? Just an idea that these are jams created by speeding up these machines.
I went through the setup and when I turned the machine on after a minute or two it threw a code 63.00.30
I have the service manual but there is no sign of any error code index. Can somebody help...
Thanks for the replies. The firmware upgrade worked and the machine comes to ready now. For a while it behaved erratically, restarting unexpectedly a few times. Then it went into a data encryption...
Hello, I'm setting up an HP E87740DN for another dealer.
Reading through the installation instructions it refers to a speed license for this series. Does the HP E87740DN require a speed license...