Search:

Type: Posts; User: Mick01

Page 1 of 15 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    1,353

    [Misc] Re: KM Bizhub Pro c6501 and ColorCal

    I seem to recall when trying colorcal if it fails to recognize the charts then you need to reposition them slightly on the glass.
    Might be worthwhile (if you haven't already) to clean the optics. ...
  2. Replies
    18
    Views
    6,956

    Re: Anyone swapped over a RIP? Got ic-306 issues!

    Hi,
    Unfortunately that dongle will not work. They are designed to be single use only. Once the update is done using the dongle it is useless.
    This was a stupid idea from EFI when this was...
  3. Replies
    8
    Views
    1,353

    [Misc] Re: KM Bizhub Pro c6501 and ColorCal

    Hi,
    To properly calibrate you need both the grey scale and the color charts. These come with the Fiery (but most of the time are thrown away).
    If you don't have these it is impossible but if you do...
  4. Replies
    18
    Views
    6,956

    Re: Anyone swapped over a RIP? Got ic-306 issues!

    Hi,
    This is testing the memory a bit but I seem to recall there being an upgrade kit for the IC-306 to allow compatibility with the C8000.
    It is an upgrade dongle.
    IC-306 have had a number of...
  5. Replies
    9
    Views
    1,500

    [CQ] Re: C7000 with RU-509 Crinkling output paper

    Hi,
    In my experience issues like this are normally stock related. Most likely the paper is wrinkling slightly going through the fusing unit first time. Those slight wrinkles are turning into the...
  6. Replies
    9
    Views
    1,500

    [CQ] Re: C7000 with RU-509 Crinkling output paper

    Without seeing samples it would be difficult for me to comment on the likely cause.
    Usually paper rippling is caused by the Fusing Separation Plate (A1DUR74H11). I would replace this plate.
    Also...
  7. Replies
    2
    Views
    599

    Re: Rat invasion of FS612

    Hi,
    Turn dipswitch 11-7 on.
    This will turn on the jam code display. You should then get a jam code (not just the screen indicating where the jam is). You should be able to then isolate down to...
  8. Replies
    2
    Views
    590

    Re: alternate lines of magenta and cyan

    This only occurs if the installation has not been completed BY THE BOOK.
    Follow the installation guide to the letter (start in the installation guide after the supply and installation of the...
  9. Replies
    3
    Views
    2,393

    [Electrical] Re: Konica Minolta C6501 CE Password

    Hi,
    The CE password is set up by the person enabling this (there is no "default" password). If this is not known you are in trouble (as you have to get into service mode to clear this).
    If this is...
  10. Replies
    22
    Views
    12,614

    Re: EFI ES-1000 Spectrophotometer

    Hi,
    If you read the PDF that Synthahol attached you will find that the license for the software is linked to a specific spectro device. Your software would most likely have been licensed using...
  11. [Misc] Re: Konica minolta press c8000 display temperature icon

    Hi,
    you are correct. It is a reading of the environment (Temp/Humidity)
    There is a sensor mounted at the rear of the PFU that gets these readings.
  12. Thread: C6708 to C-DC20

    by Mick01
    Replies
    8
    Views
    3,236

    Re: C6708 to C-DC20

    Also,
    Are you just replacing the IPB or are you swapping the whole board ass'ly (With the OACB)?
  13. Thread: C6708 to C-DC20

    by Mick01
    Replies
    8
    Views
    3,236

    Re: C6708 to C-DC20

    Hi,
    My concern is you are using boards from a KM machine. I have never dealt with this kind of security error before but assume there is firmware written to the board that distinguishes the...
  14. Thread: C6708 to C-DC20

    by Mick01
    Replies
    8
    Views
    3,236

    Re: C6708 to C-DC20

    Hi,
    C-DCxx errors relate to a security issue. It is not explained well in the service manual. It just mentions contacting KM support.
    Are you trying brand new boards for that particular model (not...
  15. Re: BHC5500 codes J1051 then it displays C3102 fuser motor not turning

    HI,
    I am assuming as you have tested the fusing unit in another machine that you have no issues with the one way bearings in the fusing drive. These are the usual cause of this code.
    I have...
  16. Thread: ibizhub 920 pro

    by Mick01
    Replies
    8
    Views
    1,039

    [CQ] Re: ibizhub 920 pro

    Hi,
    Are you referring to copying off the glass or printing via PC?
    If copying I would start by cleaning your optics. When the mirrors get dusty it lightens the image. It performs a white refernce...
  17. Replies
    6
    Views
    8,460

    Re: konica press C1085 error code c-2721

    HI,
    Leaving the error code aside, as this will most likely be resolved by replacing the power supply, you have two issues:
    1) Error operation on the Print Controller
    2) Bad Registration.

    For...
  18. Replies
    6
    Views
    8,460

    Re: konica press C1085 error code c-2721

    I will try and respond to your numerous concerns.
    C1085 machine display error code c-2107. Machine is new, only one month since installed and counter is about 73000.
    C-2107 - No such code exists?...
  19. Replies
    9
    Views
    3,682

    firmware imaging toolkit

    Hi Everyone,
    Attached is an old tool used for firmware on the older office colour devices.
    Might be useful if you still work on the old bizhubs (C250/C252 etc)
  20. Replies
    3
    Views
    3,327

    Re: KM C7000 & C-3502 / C-3501

    I can think of some things to check.
    1) Ensure TH3 (contact sensor) is contacting the surface of the belt properly.
    2) When you replaced TH1 did you set the gap correctly?
    3) Check you heater...
  21. Replies
    12
    Views
    1,575

    Re: INeo +6500 Bizhub C6500 color image problem

    Hi,
    Looks to me like you have a density balance issue. Newer models (C6000/C1070) have an adjustment procedure to combat this. No such luck with this model though. I have attached a document that...
  22. Replies
    2
    Views
    1,199

    [Misc] Re: C1060L Market Setup Mode

    HI,
    This message is displayed if the "set up" according to the installation guide has not been completed entirely.
  23. Replies
    3
    Views
    742

    [CQ] Re: Konica Minolta 6501 Shadow Gradient

    Hi,
    Usually these issues are caused by a number of items.
    1) Printer Gamma Sensor adjustment needs to be re-done. Clean the Gamma sensor and conduct the adjustment. This will set the internal gamma...
  24. Thread: Jams 72 19

    by Mick01
    Replies
    2
    Views
    790

    Re: Jams 72 19

    Hi,
    So I assume that you mean by I/O you have checked that the sensor is changing state? It would be a good idea to also clean/replace the sensor as it may be intermittently faulting.

    If so then...
  25. Thread: Bishop 7255

    by Mick01
    Replies
    11
    Views
    1,042

    [Misc] Re: Bishop 7255

    You will need to configure the TCP/IP settings on your PC's network card. Need to be within the same IP range as the IP address you gave the printer.
    Also I do recall (i might be wrong as i haven't...
Results 1 to 25 of 370
Page 1 of 15 1 2 3 4