I seem to recall when trying colorcal if it fails to recognize the charts then you need to reposition them slightly on the glass.
Might be worthwhile (if you haven't already) to clean the optics. ...
Type: Posts; User: Mick01
I seem to recall when trying colorcal if it fails to recognize the charts then you need to reposition them slightly on the glass.
Might be worthwhile (if you haven't already) to clean the optics. ...
Hi,
Unfortunately that dongle will not work. They are designed to be single use only. Once the update is done using the dongle it is useless.
This was a stupid idea from EFI when this was...
Hi,
To properly calibrate you need both the grey scale and the color charts. These come with the Fiery (but most of the time are thrown away).
If you don't have these it is impossible but if you do...
Hi,
This is testing the memory a bit but I seem to recall there being an upgrade kit for the IC-306 to allow compatibility with the C8000.
It is an upgrade dongle.
IC-306 have had a number of...
Hi,
In my experience issues like this are normally stock related. Most likely the paper is wrinkling slightly going through the fusing unit first time. Those slight wrinkles are turning into the...
Without seeing samples it would be difficult for me to comment on the likely cause.
Usually paper rippling is caused by the Fusing Separation Plate (A1DUR74H11). I would replace this plate.
Also...
Hi,
Turn dipswitch 11-7 on.
This will turn on the jam code display. You should then get a jam code (not just the screen indicating where the jam is). You should be able to then isolate down to...
This only occurs if the installation has not been completed BY THE BOOK.
Follow the installation guide to the letter (start in the installation guide after the supply and installation of the...
Hi,
The CE password is set up by the person enabling this (there is no "default" password). If this is not known you are in trouble (as you have to get into service mode to clear this).
If this is...
Hi,
If you read the PDF that Synthahol attached you will find that the license for the software is linked to a specific spectro device. Your software would most likely have been licensed using...
Hi,
you are correct. It is a reading of the environment (Temp/Humidity)
There is a sensor mounted at the rear of the PFU that gets these readings.
Also,
Are you just replacing the IPB or are you swapping the whole board ass'ly (With the OACB)?
Hi,
My concern is you are using boards from a KM machine. I have never dealt with this kind of security error before but assume there is firmware written to the board that distinguishes the...
Hi,
C-DCxx errors relate to a security issue. It is not explained well in the service manual. It just mentions contacting KM support.
Are you trying brand new boards for that particular model (not...
HI,
I am assuming as you have tested the fusing unit in another machine that you have no issues with the one way bearings in the fusing drive. These are the usual cause of this code.
I have...
Hi,
Are you referring to copying off the glass or printing via PC?
If copying I would start by cleaning your optics. When the mirrors get dusty it lightens the image. It performs a white refernce...
HI,
Leaving the error code aside, as this will most likely be resolved by replacing the power supply, you have two issues:
1) Error operation on the Print Controller
2) Bad Registration.
For...
I will try and respond to your numerous concerns.
C1085 machine display error code c-2107. Machine is new, only one month since installed and counter is about 73000.
C-2107 - No such code exists?...
Hi Everyone,
Attached is an old tool used for firmware on the older office colour devices.
Might be useful if you still work on the old bizhubs (C250/C252 etc)
I can think of some things to check.
1) Ensure TH3 (contact sensor) is contacting the surface of the belt properly.
2) When you replaced TH1 did you set the gap correctly?
3) Check you heater...
Hi,
Looks to me like you have a density balance issue. Newer models (C6000/C1070) have an adjustment procedure to combat this. No such luck with this model though. I have attached a document that...
HI,
This message is displayed if the "set up" according to the installation guide has not been completed entirely.
Hi,
Usually these issues are caused by a number of items.
1) Printer Gamma Sensor adjustment needs to be re-done. Clean the Gamma sensor and conduct the adjustment. This will set the internal gamma...
Hi,
So I assume that you mean by I/O you have checked that the sensor is changing state? It would be a good idea to also clean/replace the sensor as it may be intermittently faulting.
If so then...
You will need to configure the TCP/IP settings on your PC's network card. Need to be within the same IP range as the IP address you gave the printer.
Also I do recall (i might be wrong as i haven't...