Hi All,
I'm a Ricoh trained tech seeking some advice from you guys,
I have a friend who has a Xerox5065 with yellow streaks running through the image.
The drum has been interchanged as well as a...
Type: Posts; User: CANCOUNTRY TECH
Hi All,
I'm a Ricoh trained tech seeking some advice from you guys,
I have a friend who has a Xerox5065 with yellow streaks running through the image.
The drum has been interchanged as well as a...
Had the same problem.replace the bicu board and that will fix this issue.
Hey mate,
did they test them in another 901?
Also i forgot to mention theres a LED sequence boot up you can reference from the boards (which led's flashing sequence lights up) when you boot the...
Is it 5mm banding or oil gloss lines?
banding theres a few things you can adjust but if its oil lines there pretty hard to get rid of.
very common this, what usually happens is the side seals on the cleaniing unit wear out causing this.
Replace your bcu board.
if that fails i would swap iob1 and iob2 as a set
I have had this problem twice before.
i take it A4R is A4SEF (short edge feed only work with aussie paper sizes)
the bypass motor drives the gears that drive the rego unit (back of the drive...
Hi All,
Just an update in the printer config page i noticed ethernet speed was not set to auto.Once i set it to auto it prints like a dream.
Thanks for all the input guys.
Agree with the all these posts it is very common.
We usually add washers to the springs on the left hinge and it works all the time.Im pretty sure an rtb was released about this issue as well.
Hi All,
Have a customer with a mpc3001 at a construction site that prints building diagrams (roughly 8 pages at 5mb) it can take up to 30 minutes for the doc to print.Even trying to print the...
Hi all,
Have a mpc6000 in the field with a sr5000 finisher which is giving regular jams in the finisher shift roller section.
I have replaced the motor but still get occasional jams in this...
Had this last week.
Clean your rego sensor its probably covered in paper dust.
That should fix it.
Hi all,
Have a mpc6000 jamming at location 71.Duplex transport sensor 1.
Have replaced the whole duplex unit and fuser/ptr tray and still getting the jam.there is no physical obstruction paper...
Its good to see Ricoh dosent discriminate.In Australia we have this problem every winter every call is copy quality and within 3 weeks everything goes on to back order.only way around it for us is we...
Fiery sytem software is now version 1.2 as for colours looking crap at 50% ive experienced this the machine does not handle halftones very well if banding is occuring adjust your transfer roller bias...
Do you mean your front and back registration.
Adjusting with feed second side.
Or is this the initial run up of the machine.
If its the initial run up concentrate on getting the first side spot...
x2 you should also be hearing a clicking noise when these loose there shape.
Thanks mate toner in hopper is all fine the problem im having is the customer does around 80,000 prints a day and on these runs it goes a little greyish but then comes back to black.(Machine is in a...
All sorted mate. I know its the hdd i was trying to troubleshoot if it was the fiery hdd or gw hdd
Have had 569 error in the past and have tracked it back to a faulty vbcu board on this particular model.
Hi Guys,
Just a general question have a customer that over long runs the cq goes greyish.
Last couple of months i have replaced dev motor and cleaned out recycling tubes.
Question is has anyones...
Thanks mate thought it would come standard with this machine.
Was only going to get it for troubleshooting until i saw the cost.
Cheers mate.
Hi all,
I need to troubleshoot sc955 question is is there a sp code to bypass the fiery controller.
I have set up a port/print que and driver.
But no prints.Is there a sp i need to enable for gw...
Cheers Watson,
Swapped new dev unit and all good.
Hi all,
Has any one ever had this msg. went to replace the dev unit and this error continues to come up.
Have ordered a new harness connector for the dev unit.
Just wondering if anyone has ever...