Doh
Its a TA 5551ci but i have tried on other models and cant find it on them either
Type: Posts; User: mossup
Doh
Its a TA 5551ci but i have tried on other models and cant find it on them either
Hi Guys
Not sure if this is even possible
But one customer mentioned that when they print from a usb stick that the prints are coming out in colour, is there a way to default it to B/W...
Cool Thanks
I will get this added at set up so they can turn this on before machines are delivered
Thanks Guys
I think i found the setting under Device Setting then System on the command centre
Just to Clarify its Auto Error Clear, just that there is also Error Job Skip would this need to be...
Yes i agree
I see in the article Darry1 kindly put and it did mention slow printing , If customers have slow printing they are likely to contact their IT dept , whereas if they have an error code...
Thanks
That explains it far better than i ever could lol
Again
Cheers
I see this code in the event log on virtually every machine i go to.
One TA6052ci i went to had the code every time they printed a page from windows explorer but just certain web pages , I then...
Fixed
tmaged you were bang on with the spring.
Both springs were present but the right hand one came away missing the transfer contact.
Unusual symptom but like you said the bias is to aid...
Ago
tmaged
thanks for that i will check springs inside the machine , we haven't had any error codes mind.
We have pulled the machine to the workshop and can use the Showroom machine to quickly...
Hi Guys
Having a problem with lines on a TA 356ci
I have attached an example 35880
Really bad on first print out then gets better,
We have pulled the machine to workshop for...
Hi
We have the same problem , Replaced the said sensor and cleaned fold rollers as per CCE-1415 Tech Bulletin and still have the same issue ,our customer only do A5 booklets but jams after a couple...
The Alphard 2 range seem much better, but still poor quality, we sell Sharp Copiers as well and overall build quality is much better , but even sharp machines aren't as good quality as they used to...
Not sure about the others,but we had to change the machine to keep the customer happy, after numerous visits with Kyocera we still couldnt find a solution.
I am having a similar problem on a TA7550ci , We have changed out the following Dev unit,Drum Unit ,LSU unit Drum Drive motor ,Dev drive motor,Transfer unit , Version 7 FW . The customer have been...
Hi
Had a few of these , J131X jams , some very intermittent . i would also replace the clutch as well as that is whats causing the jamming in the first place , there are some pads to fit (302K94d70)...
Yeah had loads of the idle roller housing break causing jams and skewing , this is only on duplex so the paper comes out the side door above the idle rollers, is quite intermittent so a sod to fault...
Hi
We have a same jam code J4013 on a TA 3550ci , works fine on single pages only jams on duplex, We have had a few issues with these , machine still in warranty so may swap out side door.
Changed ribbon/Flat cables, Going to send machine back to Kyocera as it was DOA, Strange that it only F040 when connected to paper deck , Keeping an eye on the tech web site, have a funny feeling new...
Hi all
Anyone having issues with the new Taskalfa range , Unboxed one TA5501i friday and F040 (communication Engine and Main pwb) came up straight away , machine sits on a PF 730B deck, When the...
I ordered a complete PF Drive ass , in the manual it stated improved reliability so they must have issues . I also replaced the two LCC Clutches ( Feed And Transport) so hoping that will be the last...
HI
What are the jam codes you get , i have 5112 that jams intermittent from the LCC , i get PPD2 NL jams only from LCC ( although this is the main tray used) gone down the sensor route as there is...
Hi all
I am having a similar problem on a MX5112 , Very intermittent though, service print outs reveal PPD2 NL (using LCC) jams . paper jams exactly the same place , replaced modified PPD2 sensor...
I ve been back today for same problem , mag roller again starved of toner! , this time i have noticed the toner cartridge was nearly out and had toner low on the display, replaced toner cartridge,...
Thanks for all the input gives me alot more to go on, does seem to be starving the dev unit of toner , the machine i have sits along side another 820i which runs fine (apart from multifeeding from...
Have a 820i with same problem, what is the mag roller like when it runs faint?, have one that goes faint and when i checked mag roller hardly any toner on it ,seems to be lack of toner so thinking...