Search:

Type: Posts; User: Luther

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    2,033

    [Jamming] Re: J-6411/J-6111 on Kyocera 5054ci

    Have you ever found a fix for this?, we are having that issue on most 54 series with a thousand sheet finisher , one we had to replace with a 4000 sheet finisher to fix it. any help would be...
  2. Replies
    6
    Views
    1,854

    Re: DF-7100 inner tray full

    Hi guys, can someone explain where on the finisher you are putting the washers and how thick they are?
  3. Replies
    6
    Views
    675

    Re: fs-3140 continuous adding toner warning!

    did you run u130? when installing a new dv you need to run it
  4. Replies
    20
    Views
    3,358

    Re: 6002i light prints and nearly blank copies

    I would check for a bent pin in the side door connection on the machine side, it's easy to bend them and they may have been bent before you changed the conveyance section.
  5. Replies
    3
    Views
    592

    Re: Disassembly DK-5195 drum units

    the spring stays on the drum unit, there is a metal clip that aligns with the spring when you put the charge roller back in
  6. Replies
    3
    Views
    592

    Re: Disassembly DK-5195 drum units

    The blade comes out without removing the drum just remove the charge roller and you will see the 2 screws holding the blade in, the lamps should be cleaned right from the top of the drum unit, the...
  7. Replies
    4
    Views
    7,505

    [Error Code] Re: Kyocera Taskalfa 2553ci C7301

    Have you tried a new k developer unit?
  8. Replies
    12
    Views
    2,665

    Re: TaskAlfa 4002i/C9040 Error

    It's more then likely going to be disabled when you get there, do a 906 and try the DP, if the plate does not lift or it codes again it's going to be the DP board , replaced 5 or 6 for the same issue
  9. Replies
    12
    Views
    2,316

    Re: Kyocera M3540idn Jam 501

    There is no spring in the 40ppm only the 50 and 60ppm both have the lift motor, agree with previous post to change the clutch pack
  10. [Error Code] Re: Kyocera ECOSYS M3655idn - Waste Toner Bottle Not Installed

    update the firmware to the latest, we sold a bunch of this model and they all eventually had that problem, firmware fixed them all
  11. Replies
    6
    Views
    1,297

    Re: TASKalfa 508ci - toner supply replacement

    It's in the service manual beginning on page 4-4
  12. Thread: Kyocera 3510i

    by Luther
    Replies
    3
    Views
    879

    Re: Kyocera 3510i

    Also make sure all service doors are closed
  13. Thread: ricoh pro 8002

    by Luther
    Replies
    3
    Views
    1,339

    Re: ricoh pro 8002

    Sorry it was the pro8200ex, but it is rebadged as a Kyocera 13600, I replaced the DRB and the motor and all is good
  14. Thread: ricoh pro 8002

    by Luther
    Replies
    3
    Views
    1,339

    ricoh pro 8002

    I could use a little help with a code i am getting on this machine, sc 513-01, have very little experience with ricoh and just need a nudge in the general direction, have the manual but not clear if...
  15. Replies
    21
    Views
    6,231

    [Misc] Re: TaskAlfa 3252ci - Error Developer-Y

    its not adding toner to the developer unit thats why when you install a new unit the code goes away, i would pull the main drive unit and back out all the drums nd dv units, behind the main drive is...
  16. Thread: kyocera 2540dw

    by Luther
    Replies
    4
    Views
    1,066

    Re: kyocera 2540dw

    Also update the firmware when you replace the fuser, it changes some fuser timing to help with this problem
  17. Replies
    17
    Views
    3,051

    Re: KM-3252ci black only banding issue crossfeed

    I would go with the HVT, I had the same issue but it was with all the colors except black same spacing of the image
  18. Replies
    18
    Views
    4,038

    Re: Kyocera 6052ci 7620 7611 7614 7613

    I would try reseating all the connectors on the paper feed image board, then try the transfer board. those errors other then 7620 are density codes on the transfer belt for the color .7620 is only an...
  19. Replies
    5
    Views
    1,565

    [Misc] Re: Kyocera additional memory

    SD-1GB 855D200754 1GB DDR3 Memory DIMM,SD-512MB 855D200753 512MB DDR3 Memory DIMM, these are the memory options for the M5526
  20. Replies
    21
    Views
    3,709

    Re: Kyocera 3551ci cyan bands

    It's the developer for sure, you may try a dv refresh and it may clean up, but eventually you're going to have to replace it
  21. Replies
    6
    Views
    5,143

    Re: KM-3552ci jams 0512, 0502

    Hve the same issue on the PF-7110, just lube the pivot ponts, good tip !!
  22. Replies
    1
    Views
    1,061

    [Jamming] Re: ECOSYS M5526cdw top cover piece

    It belongs in the fuser, its the exit switch actuator
  23. [CQ] Re: Fs 2040dn plain white pages while printing and copying

    check the drum shield it may not be swinging out of the way, you can just remove it
  24. [Misc] Re: Kyocera 3551ci with DF770 finisher tray not lifting; always saying full...

    I would check the worm gear on the tray lift motor, the gear may be worn but works going down but cant go up that may be the buzzing you hear. i have replaced quite a few
  25. Replies
    14
    Views
    11,101

    Re: Kyocera TaskAlfa 5550ci - C6930 error

    have you done a fuser reset? u163
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4