Search:

Type: Posts; User: repn1999

Page 1 of 7 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    2
    Views
    429

    Re: MXM 754 admin Password

    small dip switch on the board, smaller than the update switch. dont remember which one it is, but one will boot the machine up in what looks like boot mode but will have the password reset option....
  2. Replies
    7
    Views
    748

    Re: MX-M904 with flasing power indicator

    DC Power supply most likely. Same symptom happens to Polaris machines and is the same fix....
  3. HP pagewide pro 577dw scanner image position off

    I had to replace a broken scanner unit on a HP pagewide 577dw. I have already entered the scanner barcode in engineering settings. The image scanned are cut off from the top about an inch. Can...
  4. Re: MX-3570 touch doesnt work/works extremely slow

    Job log could be it. If the machine has been around a while mostly before firmware 6.00 I'd say replace the msata ssd. Sharp forgot to enable trim on the ssd so they basically kill themselves with...
  5. Replies
    3
    Views
    367

    Re: MX7040/MX7580 sec transfer belt rips

    I have also seen this when techs don't powder both belts and blades properly.
  6. Thread: mx-m465n

    by repn1999
    Replies
    8
    Views
    517

    [Misc] Re: mx-m465n

    Make sure you are using yellow and 312 steric acid powder on drum AND blade. Clean off old stuff first and use a lot. There is a bulletin on which powders to use fyi.
  7. Replies
    4
    Views
    988

    Re: Sharp MX-565N & Mobile hotspots

    I would recommend not connecting directly to a hot spot. I have done this in the past and 2 things happen. First the hotspots usually have a connection timeout to save battery and sometimes they...
  8. Thread: MX-5070 H4-01

    by repn1999
    Replies
    5
    Views
    600

    Re: MX-5070 H4-01

    Make sure the firmware is up to date as well. There was a bulletin for firmware update for h4-xx codes on that series.
  9. Replies
    13
    Views
    1,723

    Re: Sharp MX-2300 with Magenta background.

    I have had to replace the mfp board and pcu board for a similar issue. looked like a blueprint once kind of, jet black background and then a color image printed on top from just a normal word...
  10. [CQ] Re: Sharp MX 3640 (several) light/choppy black copy of a copy

    So I finally got to the bottom of the issue. We put non-oem drums in these particular Aries 2 machines and this caused the black copies to be lighter and choppy. swapping with a used sharp drum fixed...
  11. [CQ] Re: Sharp MX 3640 (several) light/choppy black copy of a copy

    I generally agree with that statement, however I have some in the field that make better copies that others with the same adjustments on the same type of machine and same copy settings. I seem to...
  12. [CQ] Sharp MX 3640 (several) light/choppy black copy of a copy

    I have several sharp aries 2 machines we have overhauled that are having copy of a copy trouble on BW only. Prints look great. All the machines have new drums, dv, transfer belts latest firmware and...
  13. Replies
    4
    Views
    796

    [Dead] Re: MX-4111N SD Card

    I have the image if you still need it. I have most of the images for Sharp machines. Contact me if you still need it.
  14. Thread: MX5141 E7-11

    by repn1999
    Replies
    12
    Views
    1,870

    Re: MX5141 E7-11

    If you removed the dspf the white reference plate is gone and that's why you're getting e7-11. You have to disable it to go flat from what I remember.
  15. Thread: MX5141 E7-11

    by repn1999
    Replies
    12
    Views
    1,870

    Re: MX5141 E7-11

    I realize that the led board was not changed. I was making reference to the new style CCD unit with new sytle scn board. There is a bulletin about mixing those will cause e7-11.
  16. Replies
    6
    Views
    644

    Re: MX-3100 losing connection

    swap out the patch cable since its the easiest thing first which i assume you have done. turn off snmp on the sharp. make the site give you a new static IP for the machine for 2 reasons a)duplicate...
  17. Replies
    6
    Views
    802

    [Jamming] Re: MX-4141N with POD1_FUS power-on jam

    I had one in the field do this and we ended up replacing the connector and harness that the fuser plugs into on the frame side. not a fun job to do but it fixed it. I will also second it could be a...
  18. Thread: MX5141 E7-11

    by repn1999
    Replies
    12
    Views
    1,870

    Re: MX5141 E7-11

    I agree with the post about checking to make sure they have adequate power with a line monitor. Second could be SCU or led driver pwd. versions must match!!!! newer style with newer SCU...there is a...
  19. [Error Code] Re: MX-6240, 7040 (Polaris) with error code C1-0X (various charger cleaner trouble)

    are you using the newer MX-750MK or the older MX-620MK when doing pm? this was partially addressed in the switch to 750mk due to cleaner warping. im not aware it can be disabled nor would i recommend...
  20. Replies
    9
    Views
    793

    Re: sharp mx-m264 nv stucked

    I made images of all the replacement sd cards from sharp and do that now on all my machines. Sharp used sd because they're cheap and to eliminate mechanical failure. They never considered read write...
  21. Replies
    5
    Views
    433

    Re: MX-6500N with skew

    Is your main tech certified on this machine? I have went through the school and I am certified on it and yes 50-28 is not normally required because the factory does it however when a machine is moved...
  22. Replies
    9
    Views
    793

    Re: sharp mx-m264 nv stucked

    replace the sd card. dont swap from another machine....it caries serial info on it and you can corrupt the card from the second machine and cause 2 down machines if you swap.
  23. Replies
    10
    Views
    1,073

    Re: MX-4141 ghosting

    Doesnt matter what the drum count has one it. The powder wears off the blade over time causing it to then wear and then cause streaking. Can happen on any color. I saw it most on black. I replace the...
  24. Replies
    2
    Views
    615

    Re: MN Service Tech needed

    I might be willing to relocate for the right opportunity. I am a factory trained sharp tech with all current color certifications l, network skills, pc skills and 12 years experience on all sharp...
  25. Replies
    5
    Views
    433

    Re: MX-6500N with skew

    I would verify that the paper is being run on the proper paper setting first and that the rollers are not worn. After that I would run SIM 50-28 setup adjust then all and select the tray you're...
Results 1 to 25 of 167
Page 1 of 7 1 2 3 4