Search:

Type: Posts; User: dan7777

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    2
    Views
    75

    Re: Canon IRC3330i E302-0001

    Try scanner ribbon cable first but in my case code came back and I replaced scanner also.
  2. Replies
    4
    Views
    161

    [Error Code] Re: CAON IRADVC5250i Error E0029-003

    Check fuse FU2 on paper feed driver PCB.
  3. Replies
    7
    Views
    249

    Re: Anyone has ir8070 FIRMWARE pls ?

    No it shows. iR 8500/105/7200/85.- iR 9070/105+/8070/85+
  4. Replies
    7
    Views
    249

    Re: Anyone has ir8070 FIRMWARE pls ?

    .
    Off the canon dealer website. It only uses the service support tool. I do not even mess with trying to get someone a file that big, sorry. I do not have the time to find a site and upload it to...
  5. Replies
    7
    Views
    249

    Re: Anyone has ir8070 FIRMWARE pls ?

    You may have a hard time getting that. It shows 222Meg last version in Sept. 2008.
  6. Replies
    4
    Views
    196

    Re: No Scan Button on the touch panel

    Check all the pages. Maybe someone moved it to another page. We move the scanner, ifax and others to pages you can not see. If it is not anywhere then if it were me I would reinstall software,...
  7. Replies
    5
    Views
    296

    Re: CANON IR ADV c 7055

    If you pull the magenta developer out and see those voids on the mag roller then problem is in developer. That is one developer you can take the dr. blade out but only remove screws on top not on...
  8. Replies
    15
    Views
    641

    [Error Code] Re: E020-391 IR5030i

    Very common. If you have the plus gear with pin then look at the part that drives it. It is a toss up weather to take out the drive assembly and repair it or a friend said going in from the side will...
  9. Replies
    8
    Views
    347

    Re: Canon Advance IRC2230 jams

    Glad you found the repair. On the newer models you can touch the jam code and it tells you sensor (with picture) and if delay or stationary. On error codes it gives brief description of fix. Finding...
  10. Replies
    8
    Views
    347

    Re: Canon Advance IRC2230 jams

    Funny, I have one this morning jamming in the 2/3 delivery. 020B. 0205 is delay at reg flag. I had to replace that flag assembly on one of them. It comes on another section I do not remember but if...
  11. Replies
    3
    Views
    145

    [CQ] Re: IR C350 faded copies

    I go by percentage and mine get 80-120% before they go light with canon drums. I am going to guess that is 20-30 thousand copies.
  12. Replies
    8
    Views
    347

    Re: Canon Advance IRC2230 jams

    When you put in a fuser you have to take two screws off and put the assembly off old fuser on the new fuser. Those bushings get knocked out of place so I suggest taking the fuser out and inspecting...
  13. Replies
    8
    Views
    347

    Re: Canon Advance IRC2230 jams

    When you put in a fuser you have to take two screws off and put the assembly off old fuser on the new fuser. Those bushings get knocked out of place so I suggest taking the fuser out and inspecting...
  14. Replies
    3
    Views
    175

    Re: 0218 jam code paper deck unit c1

    Almost forgot. The hinges have been updated and I put in new hinges also. I think they were updated for that reason. It would feed from both right and left cassettes fine. Only jam from large...
  15. Replies
    3
    Views
    175

    Re: 0218 jam code paper deck unit c1

    I did on a 6XXX series. It was the right door. Either warped or worn (the guides). I think canon had a update on a piece in the middle. It was on a used machine new install. The deck may have been...
  16. Re: Canon ImageRunner Advance C3330i Error E302-001

    I only had one and replaced the cable. Code came back and ordered the scanner and cable which fixed it. My original cable was under the scanner and the newer cable was stronger.
  17. Replies
    1
    Views
    167

    Re: Rebuilding DEV's Canon c7055?

    You would have to use developer from another machine. Canon does not sell developer for this model, it comes inside a new unit. I do not know what developer you could use. I usually only replace the...
  18. [Jamming] Re: Imagepress c6000 A Jam code Of 0A13 is Occurring in Area 'D' of the Machine

    A "wrap" is an extra loop to make more tension on the spring. You take the end of the spring and loop it one more time to make more tension. If the spring is not giving enough pressure you get a...
  19. Replies
    3
    Views
    202

    Re: Adv4045 Finisher trouble

    [QUOTE=repeatcopiers;692920]Customer has Inner D-1 finisher on their Adv4045 copier. Recently is started jamming a lot but not every copy, Jam Code 1C40 and also throws E-540-0005. We thought it...
  20. Replies
    2
    Views
    194

    [Jamming] Re: Change the paper size

    This was on the canon grid.

    Log in as Administrator- System Managment settings- Notify to check paper settings- OFF

    I only have a couple of those and have not seen message.
  21. Replies
    15
    Views
    473

    Re: Canon IR 5050 intermitt blank screen, help

    There seem to be a few people here that are just plain rude. I would just ignore them. They were not here a few years ago. A couple make rude comments every post they do. You will learn their names...
  22. Replies
    7
    Views
    363

    Re: IR ADV 6255 E602-4000 and 602-5002

    There a a lot of 602 error codes. You may not have scrolled far enough. Even rev 0 had them.
  23. Re: Canon IRA C2225 Red Streak While Scanning Through Doc. Feeder

    Exactly correct. Dirty slit glass could be red, green, blue always in color but black copy would be black line. I try and train every customer to clean that glass. They seem to think it is copier...
  24. Replies
    21
    Views
    1,552

    Re: Canon ir adv 8105 dadf tray does not lift

    That is SR1 original sensor
    Service mode, copier>I/o adf feeder P001 to P007 ---P002 bit 1 should be 1 when flag pushed (original present) and 0 with no original.

    I think to get that to lift it...
  25. Replies
    21
    Views
    1,552

    Re: Canon ir adv 8105 dadf tray does not lift

    I do not think you can check the board. You can go into input and output and check if the sensor changes state. I do believe you must have the green light when a piece of paper is in the tray for it...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4