Search:

Type: Posts; User: 1stcavvet

Page 1 of 9 1 2 3 4

Search: Search took 0.15 seconds.

  1. Thread: HP 602 laser

    by 1stcavvet
    Replies
    4
    Views
    148

    Re: HP 602 laser

    that's if it's on the prints if they mean on the display ----then they're stuck in the start-up. usually they turned it off and back on again(could have had a power outage) either way you have to...
  2. Thread: HP 602 laser

    by 1stcavvet
    Replies
    4
    Views
    148

    Re: HP 602 laser

    tear in the fuser film GOOD LUCK
  3. Replies
    6
    Views
    482

    [Jamming] ricoh mpc 4502 Jams going into fuser

    Replaced a fuser film assembly that had previously blew a big hole in the film---shorted out and showed aSC544----replaced the film reset and started to test it out. jams sometimes with the leading...
  4. Replies
    10
    Views
    551

    Re: HP 4250 duplex jamming

    by the way the scotch tape is going to have you back there----it'll cut through and magnetize the arm-------- part of the end of a Q-tip stuck onto 2-sided tape works great
  5. Replies
    10
    Views
    551

    Re: HP 4250 duplex jamming

    while the machine is printing duplexing or not it doesn't need an extra paper thrown into the mix, do you see a blank sheet in there somewhere---- usually under the toner cartridge or on it's way...
  6. Replies
    10
    Views
    551

    Re: HP 4250 duplex jamming

    check out the paper feed solenoids they are notorious for becoming gummy and sticking GOOD LUCK
  7. Replies
    3
    Views
    591

    [Dead] Re: Error pictures of a Z52 Sharp copier

    replace the drum unit and the toner cartridge----if you can find any GOOD LUCK
  8. Thread: HP CM 4540

    by 1stcavvet
    Replies
    5
    Views
    419

    [CQ] Re: HP CM 4540

    The prints looked perfect and copies of those same prints are washed out All the colors and black like your looking at the page through a fog
  9. Thread: HP CM 4540

    by 1stcavvet
    Replies
    5
    Views
    419

    [CQ] Re: HP CM 4540

    Yes I did, The scanner calibrations, are more for alignment than color so I reran the color calibrations also, both from the adf and the glass. Like I said the machine does prints from the computer...
  10. Thread: HP CM 4540

    by 1stcavvet
    Replies
    5
    Views
    419

    [CQ] Re: HP CM 4540

    I'm going back to the customer Monday to check the connections on the interconnect pcb and the DC controller, any other suggestions??? Thanks
  11. Thread: HP CM 4540

    by 1stcavvet
    Replies
    5
    Views
    419

    [CQ] HP CM 4540

    I install a whole scanner unit on this machine ---Prints (supplies status page) from inside the machine were perfect and the copies(of those same pages) where all washed out. sorta overall washed...
  12. Replies
    0
    Views
    339

    [CQ] HP CM 4540 MFP

    The copies on this machine are washed out The prints from inside the machine are perfect (Status page ,config page ,etc). If I take that page that just came out of the printer and copy it it is...
  13. Re: HP laserjet 500-M551 very faint image after replacing main drive unit.

    sounds like a grounding issue, make sure the transfer roller is in properly. should be grounding on one end spring ---copper piece something. Stop the page half way check the toner cartridge if it...
  14. Replies
    2
    Views
    414

    [Wanted] Re: Ricoh MP C2800 fuser new or rebuild

    I was looking for one , but thanks I got one
  15. Replies
    2
    Views
    414

    [Wanted] Ricoh MP C2800 fuser new or rebuild

    I gotta core to send back------ if you're rebuilding
  16. Replies
    6
    Views
    558

    [Misc] Re: hp DJ T2500 plotter

    The printhead in the T2500 does not come with inks the printheads you refer to are smaller and inks are in the unit. These inks are bigger cartridges and 3 are on each side of the machine. I do...
  17. Replies
    1
    Views
    1,256

    [Error Code] Re: HP Designjet 430 Error Lights

    the first 3 lights staying on steady is for the mark encoder either the line on the roll is missing or dirty or the reader is faulty. the lights you get when you press cancel aren't listed. not all...
  18. Replies
    9
    Views
    1,488

    Re: Designjet 510, service code 86:01

    check lubrication on the rails and check slop in carrier bearings, check for noises as it goes back and forth, GOOD LUCK
  19. Replies
    1
    Views
    367

    [CQ] xerox cplor 560

    I have to replace all the drums and developer units ---can I take everything out vacuum and install everything at once and calibrate and initialize.
  20. Replies
    3
    Views
    486

    [CQ] Re: copystar CS 3550ci

    thanks for the info , feel a little better about the job now
  21. Replies
    3
    Views
    486

    [CQ] copystar CS 3550ci

    I have a color maintanance kit ---3 drums, 3 dv units etc After installing the new dv units on the drums and replacing all 3 units in the machine. there are a few sims for the dv units and another...
  22. Replies
    6
    Views
    564

    [Misc] hp dj 510 plotter

    I need to get new inks for this plotter right now all the colors are # 82---- the black is a # 10 can I put a black 82 in place of the black # 10.???
  23. Replies
    4
    Views
    692

    [Misc] Re: hp CM4540 MFP

    thank you
  24. Replies
    4
    Views
    692

    [Misc] Re: hp CM4540 MFP

    Do you mean the fuse in the fusing unit, if you mean replace the fuse----that's not the problem. it blows the fuse but never resets the count for the fuser. if you mean something else in the fuser...
  25. Replies
    4
    Views
    692

    [Misc] hp CM4540 MFP

    I tried 2 fusers (new rebuilds) and the printer will not reset I waited beyond 500 pgs with both of them. Sometimes they won't reset for 100pgs or so. This last one went 1000 pgs and still says...
Results 1 to 25 of 209
Page 1 of 9 1 2 3 4