Search:

Type: Posts; User: Printerdude

Page 1 of 5 1 2 3 4

Search: Search took 0.06 seconds.

  1. Re: Laserjet cp3525: Magenta become light from the front side of the machine

    Take a look inside the magenta toner slot, something might be dislodged creating a large gap between the drum and transfer belt. Did you try stopping the machine during a print to see if toner is on...
  2. Replies
    7
    Views
    158

    Re: HP Color LJ 3600 faint blacks

    As Lance stated, sometimes the clips from the contact-holder assembly breaks and won't hold the HV board flush with the contact-holder assembly, will cause no voltage to toner cartridges. I know you...
  3. Replies
    15
    Views
    594

    Re: HP M525 Close top feeder cover

    Replace the harness cables. These cables break because of all the open and closing of the ADF lid. One of the lead in the ribbon harness is most likely broken. Had similar problems with ADF issues on...
  4. Thread: P2015

    by Printerdude
    Replies
    1
    Views
    323

    Re: P2015

    I see no problem swapping a non network formatter board for this printer.
    Make sure to match duplex formatter to duplex printer and non duplex formatter to non duplex printers.
    It still might work...
  5. Re: HP LJ Pro 400 M401dn programming new Serial number and page count

    Is this a new or used formatter board? Doing a NVRAM will clear the serial number, but you can't create a new number.
  6. Replies
    6
    Views
    1,757

    Re: Leading edge folded on M712

    Did you check the ream of paper in tray 2 for folded paper. Have seen paper either crease or folded right out it the package. Also, check the tray paper length/width guide is set correctly.
  7. Replies
    4
    Views
    1,067

    Re: Scanner error 13, MFP 477

    Have you reattach the cables to the scanner itself?
    Does the scanner assembly move freely?
  8. Replies
    4
    Views
    1,067

    Re: Scanner error 13, MFP 477

    Are you sure the display is showing scanner error 13??? or are you guessing a error 13 is scanner issue?
    Error 13 are usually related to paper jams.
    Error 30 are related to scanner errors.
    What is...
  9. Replies
    12
    Views
    669

    [CQ] Re: Faded print on HP Color 4600

    Forgot, thanks. Edited previous post.
  10. Replies
    12
    Views
    669

    [CQ] Re: Faded print on HP Color 4600

    Since printing issue is happening with two different computers, let's look at the printer itself.
    Make sure economode is off.
    Did you do a cold or NVRAM reset?
    Did you swap the black cartridge to...
  11. Replies
    17
    Views
    1,212

    Re: HP CLJ 4600

    Upon taking a closer look of the test samples, all the colors except the black seems to be off or the black is off and not the colors.

    Laser scanner itself might be misaligned.

    Have you try...
  12. Replies
    9
    Views
    707

    Re: HP M632, image shift.

    Don't rely to much on your support guys.

    Wild Bill is in the right neighborhood. I know there should be an adjustment for each tray, why remove this setting on a newer printer?

    This is what...
  13. Replies
    17
    Views
    1,212

    Re: HP CLJ 4600

    There is a DC controller calibration reset. Try this procedure.
  14. Replies
    9
    Views
    535

    Re: LJ 4250 ghosting

    Copyman,

    By any chance do you still have the original packaging the fuser came in and provide a picture of the packaging and the fuser assembly with the serial number?
    May be able to help you to...
  15. Re: HP LaserJet M608 Not seeing Tray 2 "Tray 2 overfilled or roller issue"

    Great tip! Had other HP models with the paper size sensor assembly dislodged.
  16. Re: HP LaserJet M608 Not seeing Tray 2 "Tray 2 overfilled or roller issue"

    Did someone mentioned right paper guide? I read left paper guide.
  17. Replies
    9
    Views
    487

    [Misc] Re: HP P4515 Formatter

    My mistake, the engine cycles count can be modified. But try this.

    Print out the usage page from the Information menu, the usage page will have list of impression made. If you think the engine...
  18. Replies
    9
    Views
    487

    [Misc] Re: HP P4515 Formatter

    No! You can't reset the engine cycles counter on this model.
    If you're planning on swapping out the formatter with you old machine, print out the configuration page with the page count and network...
  19. Replies
    9
    Views
    744

    Re: Hp M451n color

    I see there isn't a lot of parts available for this model, mostly major assemblies. Glad it worked out for you.
  20. Replies
    9
    Views
    886

    Re: M651 Error 50.2F

    Do you have the original fuser? I you do, put it in and leave it in to see if the problem persist. This really sound like a refurb fuser.
  21. Replies
    9
    Views
    744

    Re: Hp M451n color

    Just a little baffled. Didn't you replace the fuser and had the same problem? You removed a part from the old fuser and put it in the new fuser and it solved the problem? If you replaced the sensor...
  22. Replies
    6
    Views
    596

    Re: What makes a 3015DN duplex?

    The tray you are referring to is called a duplex media feed assembly, it is install in all models of the P3015 series. Every model other than the "D" series have a non functioning duplex media feed...
  23. Replies
    16
    Views
    1,451

    Re: 4250 Jamming from tray 2

    You mention tray 2 paper pickup roller keeps cycling up and down, is it picking up paper when this happens? If not, check the paper tray back stop is set to correct position and not broken. If yes,...
  24. Re: Hp color laserjet cp4525 68.0 permanent storage full problem

    Regarding the 68.0 error, does this error comes up when powering up? Does it clear at all?
  25. Replies
    9
    Views
    642

    Re: CP3005X print out blurry

    Try the cold reset and NVRAM first. Then replace the DC Controller.
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4