Search:

Type: Posts; User: CopierNerd

Page 1 of 5 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    2
    Views
    233

    bizhub 654e Error code c-6753 and 9401

    Greetings!

    Machine is bizhub 654e. Total Copies/Prints produced is only 10K. First the error code was c-9401 which is related to CCD and Lamp. Lamp is turning ON. Tried to reset it several times...
  2. Thread: C6753

    by CopierNerd
    Replies
    4
    Views
    875

    Re: C6753

    I am also facing the same problem. error code c6753 even ADF is unset but DSPB board is plugged. Its the board or cables? I am also getting c9401.
  3. Replies
    4
    Views
    360

    Re: Bizhub 958 vs Bizhub 758

    For 80K copies per month 758 is enough even for 150K. Bizhub 958 is recommended for avergae 300K copies or above. So i would recommend to buy 758 if monthly volume is ranging from 80,000 to 150,000...
  4. Replies
    20
    Views
    1,912

    [Misc] Re: Konica Minolta ADF burned by patient

    Patient wants us to be patient and think about it! Never saw this before.
  5. Replies
    33
    Views
    2,802

    [Jamming] Re: bizhub 423, 93-10 , Duplex/Switch Back

    Allan! ITS BACK!

    I am afraid, Its back! Jamming in Duplex. Lubricating the duplex bushing, motor and belts was not long lasting.
  6. Replies
    6
    Views
    423

    Re: Oily Substance on Fuser Rollers

    I have asked the same in one post and few Seniors replied. I think this oily or sticky substance is toner wax or polymer.which is included in toner and one of its ingredient. A little amount from...
  7. Replies
    14
    Views
    960

    Re: B554e J30-03

    J30-03, Paper jams at 11. Paper gets into fuser and stops. How much it gets in? if you have replaced all things mentioned then you should check transfer belt drive. Transfer belt is not rotating. You...
  8. Re: Stop acting like a thief. meter reset requests

    Totally agree with synthohol.

    At this forum one cannot determine whether the person who is asking for reset tool or relevant stuff will use it for positive means or not. I believe resetting the...
  9. Replies
    19
    Views
    1,524

    Re: KM BH258 Printing problem

    As far as i know you cannot buy developing roller only. Its whole developing unit as you know it. There is no part number for this single part. You can take it from old developing units if you do not...
  10. Thread: C-C163 C368

    by CopierNerd
    Replies
    9
    Views
    623

    [Error Code] Re: C-C163 C368

    C-C163 incorrect firmware type.

    MFP board and print control board replacement at the same time is strictly prohibited. If MFP board have been replaced by your junior tech then You should install...
  11. Re: Problem Bizhub c220 white spots on recycled cardboard +PHOTOS

    According to me its media's fault. Prints on plain are fine. This media has problem because its rough . If you want to see by yourself just make prints on fine quality non-recycled cards of same...
  12. Replies
    5
    Views
    462

    Re: C-0204 Bizhub 227

    What can i say when copier Gurus have said everything you need. I will add, you can check whether paper jams in 2nd tray or not like the customer is saying so, in service mode>counter>Jam...
  13. Replies
    2
    Views
    267

    c1100 tearing Fusing Belts

    bizhub press c1100 is tearing fusing units. I have replaced 2 fusing belts.Both goes at one side. sensor is OK, double checked. Cleaned it. Lubricated the fusing rollers with silicone oil for...
  14. Replies
    19
    Views
    1,524

    Re: KM BH258 Printing problem

    You have swapped drum units but the problem is still there. So issue is not with the drum units. It is cleared.

    Now come to the second point which is Transfer belt, you have replaced transfer belt...
  15. Replies
    1
    Views
    14

    bizhub 367 Unable to Print

    New problem!

    bizhub 367 is unable to print from network and from USB cable. Print from external memory is OK.

    Symptoms> Network port lights are dead, no blink. Even not printing over usb by...
  16. Replies
    33
    Views
    2,802

    [Jamming] Re: bizhub 423, 93-10 , Duplex/Switch Back

    Allan! I went there again. This time not with old used side door but with the idea to check the harness. If any wire is damage inside. I removed the side door. Removed the metallic plate and torn the...
  17. Replies
    9
    Views
    848

    Re: konica minolta -- bizhub fusers

    Pleasure!
  18. Thread: C558 noise

    by CopierNerd
    Replies
    20
    Views
    1,756

    Re: C558 noise

    I agree. if its squeaking noise then probably the cause is transfer roller. One can also check by removing the transfer roller and also by manually rotating the tr roller. Lubricating the seating...
  19. Thread: C558 noise

    by CopierNerd
    Replies
    20
    Views
    1,756

    Re: C558 noise

    Yes, Sir Wayne is right! Its the fusing cleaning roller bushing. experienced this yesterday but mine was 658e.
  20. Replies
    9
    Views
    848

    Re: konica minolta -- bizhub fusers

    All Images with 1 name is fusing unit of bizhub 552/652

    and the images with 2 name in JPEG is fusing unit of 658/658e, 458/458e, 558/558e, 758/758e,
  21. Replies
    9
    Views
    848

    Re: konica minolta -- bizhub fusers

    There is no such thing as part number mentioned on fusing units if they are out of the box. Nope! All you have to do is to look all of them and make their categories, say those are same. take their...
  22. Replies
    33
    Views
    2,802

    [Jamming] Re: bizhub 423, 93-10 , Duplex/Switch Back

    I didn't go there again to check. Customer informed me over the phone that it jams sometime and sometime don't. So they are using it anyhow. I think whole door replacement is the last resort.
  23. Replies
    5
    Views
    391

    Re: ID toner once out of box

    Toner Model: TN-513, Machine Model:bizhub 364/454/554
    Toner Model: TN-515, Machine Model: bizhub 368/458/558

    There is no other way to know without trying.
  24. Replies
    38
    Views
    4,008

    Re: SMB ISSUE WINDOWS 7

    Scan to HDD, User Boxes are more reliable in my opinion. There is no need of internet and user will not have to open mail accounts and then download from there. Its quite simple and reliable. :o
  25. Replies
    38
    Views
    4,008

    Re: SMB ISSUE WINDOWS 7

    No need to remove update. Just restore the changes made by update in SMB and file sharing.
Results 1 to 25 of 116
Page 1 of 5 1 2 3 4