Search:

Type: Posts; User: xring1958

Page 1 of 3 1 2 3

Search: Search took 0.62 seconds.

  1. Replies
    17
    Views
    1,261

    Re: You won't believe it........

    I bet the people who sell RainX miss analog ADF units.
  2. Replies
    4
    Views
    292

    Re: Wierd Issue with MX-M623

    Popped the cover on the ADF and there was a big ole paperclip lying right next to the board.

    pulled it reassembled tested 200 copies and lifted adf a bunch no failures.

    Delivered to customer...
  3. Replies
    4
    Views
    292

    Wierd Issue with MX-M623

    OK Guys,

    I had a call for buzzing noise on a 623. turned out the Surge suppressor was buzzing but still functioning.
    I replaced the surge suppressor & was good to go. About a week later I got a...
  4. Replies
    6
    Views
    379

    Re: MX-B355W Opinions

    I am old enough to remember that almost any Sharp ending in 10 was to be avoided SF-710 SF-810 were among my first exposures to dry bond copiers and both had lots of updates and field...
  5. Replies
    6
    Views
    379

    Re: MX-B355W Opinions

    Do you have a specific reason about this unit or do you just generally distrust this class of machine.

    Thanks
  6. Replies
    17
    Views
    1,261

    Re: You won't believe it........

    The 60 copy and 76 cop analogs were rebadged Minoltas they even had some rebadged Xerox and Toshiba units usually at the larger CPM sizes
  7. Replies
    10
    Views
    526

    [Misc] Re: Sharp 5141 mega scan size

    Check the scan settings if it is B&W one may be set to Grayscale The Mono 2 setting will lower the file size,
  8. Replies
    6
    Views
    379

    MX-B355W Opinions

    I am usually very wary of A4 desktop MFPs and usually suggest a full sized unit if possible. I have a Client that has been using Panasonic desktop MFPs with Fax DP-190s that are now on their last...
  9. Replies
    17
    Views
    1,261

    Re: You won't believe it........

    Panasonic had a contribution. Before Panasonic all of the machines I worked on Sharps, Canons Minoltas even some Royals and SCMs used a main motor with chains or belts and clutches. Panasonic was...
  10. Replies
    3
    Views
    425

    Re: Close right side door MX-4141

    And the Winner is WOKO . The call was being run by two of my Junior techs one with little electrical experience & other really just a trainee. Neither chased the door switch wire back to the DC PWB...
  11. Replies
    3
    Views
    425

    Close right side door MX-4141

    Have a MX-4141 that says to close the right side door. We have checked the Micro switches front & rear replaced PCU Board & AC Control Board.
    Checked 24 V from DC Board still no go. when we do the...
  12. Re: Sharp Mx-m264n blank streaks across scans and prints.

    Why would any of the print engine parts affect scans?
  13. Replies
    11
    Views
    1,228

    [Misc] Re: Sharp MX M363 Install Fuser Web

    It is kinda tough the first few you do but gets easier.
  14. Replies
    7
    Views
    819

    Re: Conectivity issue with MX-503

    This is happening immediately when it turn off and back on if it was an IP conflict I would be able to ping the IP address and get a pely with our machine off. & too late all hair is gone.
  15. Replies
    7
    Views
    819

    Conectivity issue with MX-503

    OK Guys here is a weird one that I am posting in Sharpsection and Connectivity section.
    We have a Sharp MX-503 that we installed about six monthsago that immediately had connectivity issues. The...
  16. Replies
    3
    Views
    500

    Sharp MX- 503 connectivity issue

    OK Guys here is a weird one that I am posting in Sharpsection and Connectivity section.
    We have a Sharp MX-503 that we installed about six monthsago that immediately had connectivity issues. The...
  17. Replies
    9
    Views
    654

    MX-7040 only prints Black?

    OK we got this in used. The color copy button is greyed out and not functional but it will copy in black we have updated firmware replaced a bunch of boards reset defaults & looked for any setting...
  18. Replies
    2
    Views
    276

    Re: mx-m623 admin password

    I have done this on older MFPs like MX 3100N Pull MFP Board on unit with security kit remove security kit memory and Prom put Prom and memory from a second machine into first machines MFP Board Put...
  19. Replies
    12
    Views
    688

    Re: Sharp MX-6050 does not boot.

    Your Might was autocorrected to Mind

    Many times the manual offers a lot of might be solutions and actual experience may narrow down the possibilities.
    If every time I replaced the first thing...
  20. Replies
    12
    Views
    688

    Re: Sharp MX-6050 does not boot.

    We had a 3070 do this to us. Sharp said to replace the MSATA Board ( this is the new SD) and the Flash ROM plus there is a very small ribbon cable on SCN MFP Board that they said needed to be...
  21. Replies
    1
    Views
    241

    Re: sharp mx5001n eproms

    If you replaced the board you will need to move the e-prom from old board & put it in new board. If it was working then it gave you a code you might want to pull e-prom and re insert. If you need a...
  22. Replies
    29
    Views
    18,680

    [Misc] Re: Admin Password reset

    If you have a DSK and need to reset password you may be able to move MFP Board to another machine without a DSK swap PROM then update. This has worked for me on older units like MX-3100. also had to...
  23. Replies
    3
    Views
    429

    Re: F2-72 F2-73 on MX3060

    Look closely at the openings in the developer units & make sure the clear seals have been removed. This happened to us.
    I don't think re running 25-02 with no toner ever added would cause an issue...
  24. Replies
    10
    Views
    1,256

    Re: Sharp MX-3050N F2-67 code

    Panasonic color units came that way also. However what would be the issue if you ran 25-02 without installing toner ctgs. Shouldn't it find the same density values?
  25. Replies
    10
    Views
    1,256

    Re: Sharp MX-3050N F2-67 code

    Still interested in what you found. A few days ago we had a very experienced field tech set up a 3070 in shop.( Not what he usually does) When removing the strings that tether the temporary Mylar...
Results 1 to 25 of 55
Page 1 of 3 1 2 3