Search:

Type: Posts; User: 1stcavvet

Page 1 of 8 1 2 3 4

Search: Search took 0.24 seconds.

  1. Replies
    4
    Views
    303

    [Misc] Re: hp CM4540 MFP

    thank you
  2. Replies
    4
    Views
    303

    [Misc] Re: hp CM4540 MFP

    Do you mean the fuse in the fusing unit, if you mean replace the fuse----that's not the problem. it blows the fuse but never resets the count for the fuser. if you mean something else in the fuser...
  3. Replies
    4
    Views
    303

    [Misc] hp CM4540 MFP

    I tried 2 fusers (new rebuilds) and the printer will not reset I waited beyond 500 pgs with both of them. Sometimes they won't reset for 100pgs or so. This last one went 1000 pgs and still says...
  4. Replies
    2
    Views
    281

    Re: Hp laserjet p3015 13.01.00 error

    be sure to put some silocone grease on the rollers in the rear door and check the motion of the paper in the cassette is not rubbing as you feel the rising motion of the paper GOOD LUCK
  5. Replies
    8
    Views
    513

    [Jamming] Re: Sharp mx c3140 ADF jams

    thanx again
  6. Replies
    2
    Views
    276

    [Error Code] Hp designjet 4520 86-01 code

    Customer said it would do this every once and awhile----Of course ----Called me to replace the shredded carriage belt, Put the belt on start it up goes thru initialization and comes back to the...
  7. Replies
    8
    Views
    513

    [Jamming] Re: Sharp mx c3140 ADF jams

    Can you get to the sensor by pulling back the platen cover and get to it from the bottom??? and thank you very much with all the printer solenoids and flags I have to repair I never thought of...
  8. Replies
    8
    Views
    513

    [Jamming] Re: Sharp mx c3140 ADF jams

    no!!! it makes it past the slit glass and sorta crumples up in the throat of the exit. like it's crashing into dead rollers. after that initial jam it'll run like a champ as long as it's not a...
  9. Replies
    8
    Views
    513

    [Jamming] Sharp mx c3140 ADF jams

    The 1st page thru this ADF jams-------stops as it leaves the slit glass to exit, and bunches up. If you remove it and start again the machine will run all day till it's left to sit for awhile again....
  10. Re: Samsung SCX-6545N Lines when scanning through ADF

    The problem is your customers printers are not fusing properly, the toner is coming off as they pass through the feeder. they're using compatable toner that wont stay on the paper or the printers are...
  11. Replies
    3
    Views
    1,935

    secret to seeing new posts

    When I click on new posts I get redirected to What looks like a google search, how do I get to the new threads they're piling up HELP
  12. Replies
    4
    Views
    599

    Re: HP DesignJet Z3200ps 87.10 error

    first couple things I'd check is that the encoder strip is seated in it's mount properly and see if the sensor on the carrier that reads the strip isn't loose or out of position GOOD LUCK
  13. Re: HP Officejet Pro x476dw MFP Duplex unit life

    Is there a reset procedure when you replace it? I just was talking to a guy who installed a new one and never got rid of the duplex unit full message.
  14. Replies
    23
    Views
    2,051

    Re: Mpc4502 wrinkling through fuser

    the rollers aren't straight the further the paper goes to the edges of the fuser the worse it is, check the bearings or where they mount GOOD LUCK
  15. Thread: Kyocera 4035

    by 1stcavvet
    Replies
    5
    Views
    546

    Re: Kyocera 4035

    yes, it's a malfunction reset you'll see it when you get there execute it then turn the machine off and on again---- if you don't see it in 906 look at 960 it's been a while pretty sure it's 906 ...
  16. Thread: Kyocera 4035

    by 1stcavvet
    Replies
    5
    Views
    546

    Re: Kyocera 4035

    try sim 906 to recover good luck
  17. Replies
    1
    Views
    280

    [Misc] Hp laserjet M4555 mfp WON'T COPY

    WON'T COPY, pages go thru feeder and comes up says on the screen copier control disabled. When the screen comes ready The copy square comes on. The fax square never comes on --No fax attached. If...
  18. Replies
    5
    Views
    415

    [CQ] Re: FS-9530DN White Lines

    little ball of fuzz inside the screen of the charger (main charge)
  19. Replies
    9
    Views
    746

    Re: Hp M451n color

    I'd check paper size, make sure that's right, and then try paper thru the bypass that would eliminate a sticky solenoid. other than that I'd say registration switch sticking. You never said ---What...
  20. Replies
    6
    Views
    687

    [Jamming] Re: hp laserjet m725

    on this machine there is no torque limiter, the whole assembly is brand new. comes all one piece like the old 3005 or 24XX series I bought it brand new and had to dissemble it and fix the problem. ...
  21. Replies
    6
    Views
    687

    [Jamming] Re: hp laserjet m725

    turns out the seperation roller in the new sep assembly was too tight took it apart and greased the clutch spring and reassembled and took off running like a champ
  22. Replies
    6
    Views
    687

    [Jamming] Re: hp laserjet m725

    it'll feed 100 sheets of paper and maybe 20-25 will have this wide (1-1 1/2) knick in the leading edge. It doesn't always jam if it does jam the paper never leaves the drawer. That's why I wanted to...
  23. Replies
    6
    Views
    687

    [Jamming] hp laserjet m725

    The paper coming from the 2nd cassette is putting a nick in the paper about 1-1.5in wide right in the middle of the leading edge. sometimes it's bad enough to stop the paper from feeding out of the...
  24. Replies
    2
    Views
    427

    [Error Code] Re: hp clj CM4540 error code 57.10.01

    the fan housing is part of the frame that holds the hard drive--- might you know why I'm getting this code--- that's definitely the code and there is no fan in the formatter the fan is 22.00 and...
  25. Replies
    2
    Views
    427

    [Error Code] hp clj CM4540 error code 57.10.01

    I can't find this code in the svc manual when I called tech support they said it was a formatter fan I pulled the formatter and there is a place for a little fan but it's not there, I can't believe...
Results 1 to 25 of 187
Page 1 of 8 1 2 3 4