Search:

Type: Posts; User: cscce

Page 1 of 6 1 2 3 4

Search: Search took 0.39 seconds.

  1. Replies
    0
    Views
    81

    [Misc] Oce Colorwave 600/650

    I have read rnelson's post about problems with Oce 600 and 650. I'm looking for more opinions so I can give management as much info as possible about reliability, parts availability, etc.
    I know...
  2. Replies
    0
    Views
    94

    Colorwave 600, 650; also TC4 scanners

    We are considering a proposal to service Oce' Colorwave 600 and 650 printers along with TC4 scanners.
    How are these machines in terms of reliability, access to repair parts and service manuals, etc?...
  3. Thread: SP5210 SP Mode

    by cscce
    Replies
    7
    Views
    739

    Re: SP5210 SP Mode

    Thank you very much to all who responded. The 107 key sequence worked, but only after I replaced the HDD. With a dead drive or no drive at all I could not get to SP mode.

    Now I have another...
  4. Thread: SP5210 SP Mode

    by cscce
    Replies
    7
    Views
    739

    SP5210 SP Mode

    I have a SP 5210 that needs a hard drive replaced. I haven't been able to find the key sequence to get into SP mode. Reset>806182>C doesn't work nor does the old "107" code.
    Any ideas?

    Thanks in...
  5. Replies
    7
    Views
    514

    [Electrical] Re: CLJ CP4525 formattor battery

    The 4525 formatters I've seen all have the battery connectors spot welded to the battery. Suggest you pull the cmos battery holder off an old PC motherboard.
  6. Thread: HP CLJ 4600

    by cscce
    Replies
    17
    Views
    1,214

    Re: HP CLJ 4600

    Have you reset the lasers to "home" position? If not, try this - it worked for me on a 4700.
    Laser re-alignment procedure is as follows:


    Let machine warm up and indicate ready
    Open upper...
  7. Thread: 59.F0 Error code

    by cscce
    Replies
    1
    Views
    394

    [Error Code] 59.F0 Error code

    I had a HP CP4525 printer that was giving a 59.F0 error at every boot up, making the printer unusable. The cause turned out to be a failed DC Controller.
  8. Replies
    6
    Views
    425

    [Misc] Re: Toner Dispenser Pipe Removal

    I figured it out. It's a single unit that handles all 4 colors rather than one unit for black and a second one for CMY.
  9. Replies
    6
    Views
    425

    [Misc] Re: Toner Dispenser Pipe Removal

    So, am I correct: the toner pipe is held in by two screws at the front and mounted on two alignment pins at the rear?

    Thanks,
    Mike
  10. Replies
    6
    Views
    425

    [Misc] Re: Toner Dispenser Pipe Removal

    Thanks for replying.
    In this case, with the toner cartridge removed and interlocks cheated: starting to print a supplies list I can see that each time the click is heard a puff of toner comes out of...
  11. Replies
    6
    Views
    425

    [Misc] Re: Toner Dispenser Pipe Removal

    Thanks for the tip.

    Mike
  12. Replies
    6
    Views
    425

    [Misc] Toner Dispenser Pipe Removal

    I have a WC7845 that makes a clicking noise. I have traced this to a jammed black toner dispense pipe. It appears that the pipe assembly is only held in place by 2 screws in the front and mounts on 2...
  13. Re: Canon C5051 dumped cyan toner, replaced toner & cleaning blade, now no cyan

    [QUOTE=Keith N;584984]Ok, I swapped the cyan and magenta drums and it looks like I'm getting some cyan now, but it fades toward the top of the page. Oddly enough though, the magenta coverage seems...
  14. Re: Canon C5051 dumped cyan toner, replaced toner & cleaning blade, now no cyan

    Looks like cyan and yellow drums are both worn out. Swap the cyan with the magenta drum and see if symptoms change. Also, clean the laser lenses just to rule that out (you've probably already done...
  15. Replies
    12
    Views
    1,708

    [Misc] Re: Xerox 4110 Transfer belt keeps tearing

    Do you have a photo of a ripped transfer belt?
  16. Re: Canon C5051 dumped cyan toner, replaced toner & cleaning blade, now no cyan

    Looks like the cyan developer is worn out and so is the yellow drum.
  17. Replies
    2
    Views
    350

    Re: IRA c5030 Magenta Mis-registration

    Today I replaced the magenta dev unit. Problem solved.
  18. Replies
    8
    Views
    515

    Re: HP 1055cm no magenta

    I think I just found it. It's in Utilities > Display Contrast. I was looking for brightness instead of contrast.
    I'll know for sure tomorrow.
  19. Replies
    8
    Views
    515

    Re: HP 1055cm no magenta

    Problem solved. It was the main board. Now there is just one more thing.
    The main board I installed came from a retired 1055cm PLUS. The machine I've been working on is a 1055cm (not a Plus model)....
  20. Replies
    2
    Views
    350

    IRA c5030 Magenta Mis-registration

    I'm seeing a strange problem with a Canon c5030. The machine has 390K copies and I'm pretty sure the developing units have never been replaced. Replacing the magenta drum had no effect. Could this be...
  21. Replies
    8
    Views
    515

    Re: HP 1055cm no magenta

    Thanks!
    I'm the adventurous type so I'd like to take a shot at the flex cables. It's unclear to me how to pop the top off of the carriage to get to flex cable connections. Any advice?

    Mike
  22. Replies
    8
    Views
    515

    Re: HP 1055cm no magenta

    Thanks. I used an HP plotter maintenance kit to clean the contacts.
    The problem before replacing the cables was the that magenta printhead was always flagged as faulty. This happened with 4...
  23. Replies
    8
    Views
    515

    HP 1055cm no magenta

    After replacing the trailing cables and thoroughly cleaning the contacts on the carriage and on the printheads the self test indicated all printheads OK and full or nearly full. When the alignment...
  24. Replies
    4
    Views
    508

    [Error Code] Re: Designjet 1055cm problem

    Many thanks for the info. I checked this morning and, not surprisingly, there's air in 3 of the ink lines so an new tube system will be installed.

    Mike
  25. Replies
    4
    Views
    508

    [Error Code] Re: Designjet 1055cm problem

    Thanks! I will swap out all printheads today.
Results 1 to 25 of 138
Page 1 of 6 1 2 3 4