Search:

Type: Posts; User: Toxic

Page 1 of 5 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    10
    Views
    278

    Re: Yello bands on KM c1070

    Lol,that maybe work in some cases with some people.
    I agree that should be normal procedure.
    In my case when developer depleted second time in about 400k i contact my technical support from KM and...
  2. Replies
    10
    Views
    278

    Re: Yello bands on KM c1070

    I have this problem on C1060l with only cyan developer.
    2 times change developer then search for problems and find firmware which solve this problem.
    If i remember good it was GCD-25 firmware
  3. Re: bizhub 750 paper stuck on separation drum claws

    Looks like problem is about humidity,temperature,moisture in paper...
    Did you try some other paper brand ?
  4. Replies
    17
    Views
    875

    Re: KM C258 offsetting issue

    When you replaced ITB did you replace transfer roller,just guess...
  5. Replies
    4
    Views
    218

    Re: Di-183 strange problem

    Have similar problem few times on Bizhub 163 and it was bad "start" microswitch.
    Usually when that is problem you can not feel microswitch to click on touch,its like microswitch is not there and if...
  6. Replies
    7
    Views
    280

    Re: Dead control panel bizhub c224e

    @copyman
    Exactly point to my case with this speciific machine i already mention.
    But it was nice to spent some time with nice girl working there and after work,testing machineis working ok...
  7. Replies
    7
    Views
    280

    Re: Dead control panel bizhub c224e

    I agree ,i would consider to change mfpb only if machine is low clicks and very good condition,better to sell new one,if they dont do much prints and not demanding C227 can do the job.
    About...
  8. Re: [PHOTO] Magenta and cyan vertical lines on first copy KONIKA MINOLTA C220

    Is it occur on all paper types and weights?
    Toners are original OEM or replacement?
  9. Replies
    4
    Views
    1,830

    Re: C1070 error c3511

    Few days ago on C1060l i have C3511 and 3513 after warming up.
    Replaced fusing temperature sensor/1 (non contact sensor) ,problem solved.
  10. Re: [PHOTO] Magenta and cyan vertical lines on first copy KONIKA MINOLTA C220

    What is distance betwen 2 magenta lines?
    If it is about 96mm it is drums memory problem,maybe someone exposed drum to sunlight,etc...
  11. Thread: C554e

    by Toxic
    Replies
    4
    Views
    331

    [CQ] Re: C554e

    You may not be aware of what they are capable of doing to some end users.
    At least what i saw on the field.
  12. Thread: C554e

    by Toxic
    Replies
    4
    Views
    331

    [CQ] Re: C554e

    You could do some search,forum is full of solutions like this.
    Are you tech or end user?

    http://www.copytechnet.com/forums/konica-minolta/101623-c-2557-c554e.html?101623=#post483645
  13. Replies
    3
    Views
    200

    Re: faxes frozen - bizhub 4020

    Check firmware version and update if it is old.
    These models have many problems with fax functioning and been solved with newer version of firmwares.
  14. Replies
    10
    Views
    443

    [Misc] Re: DR-012 Humidity problem

    Strange situation...
    Does it matter what is drum life when starts making this problems?
    How do you clean drum and after cleaning it is ok?
    First and last time i was cleaning drums every few days...
  15. Thread: Bizhub 283

    by Toxic
    Replies
    12
    Views
    571

    Re: Bizhub 283

    Not even close to match that but you can try,i am curious about results...
  16. Re: c6501 with Fiery IC-408 - FF code - loads winxp fine - no EFI controller - option

    CWM should be installed and run from PC, type ip adress and connect to fiery.
    I never tryed to use files from backup partition because you can easy install system software over lan cable from pc or...
  17. Re: c6501 with Fiery IC-408 - FF code - loads winxp fine - no EFI controller - option

    Go try then to end process "fiery.exe" and then go to aplications-new task,type fiery.exe -enter
    It should launch some cmd windows with executing commands.
    Wait sometime till that end and check...
  18. Re: c6501 with Fiery IC-408 - FF code - loads winxp fine - no EFI controller - option

    I never see system corrupted and still can access remotely and log in to fiery system but that is not for sure that system is not corrupted anyway.
    Did you try to check and reconnect cable and...
  19. Replies
    7
    Views
    382

    Re: Wierd fixing problem in konica c6000

    I agree,post sample with more color and bigger size.
    Try rotating fuser belt,i think you will see damaged spot.
    Fuser belts on this machine starts to falling of at 400-600k prints.
  20. Replies
    7
    Views
    382

    Re: Wierd fixing problem in konica c6000

    What is condition of fusing belt?
    Some photos of prints,fuser,... could not hurt to post here.
  21. Thread: C6500 Softswitch

    by Toxic
    Replies
    11
    Views
    692

    Re: C6500 Softswitch

    How did you get idea for that specific dipws and what is function of it?
    Just curious.
  22. [Misc] Re: bizhub c252 Rectangle spot on scans after NVRAM reset

    Folow this procedure exactly and it should be ok
    40388
  23. Thread: Bizhub Pro c6500

    by Toxic
    Replies
    7
    Views
    378

    Re: Bizhub Pro c6500

    To see basic parts life (drum,developer,charge units...) just press "utility/counter" button and "details" i think,and you see and can print list with counters.
    For detail parts counter press...
  24. Thread: Bizhub Pro c6500

    by Toxic
    Replies
    7
    Views
    378

    Re: Bizhub Pro c6500

    I agree,dont involve if you can.
    I have 3 of similar machines (C5501) in working state and still dont have problems with parts,i use DU-104 drum units and lots of parts fits from C6000 for...
  25. Replies
    3
    Views
    303

    Re: C364 Skewed Images Issue

    I have similar problem once on brand new out of the box C224e and try everything like you did.
    There was color registration problem and skew problem.
    Solution was to replace PH unit.
Results 1 to 25 of 110
Page 1 of 5 1 2 3 4