Search:

Type: Posts; User: roho

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    5
    Views
    207

    [Jamming] Re: CFU AM1 Adv C 5560

    This generation doesn't use those rollers anymore, neoprene.
  2. Replies
    3
    Views
    175

    [Misc] Re: Noisy Y2 Booklet Finisher

    The booklet maker is noisy and clangs, normal. I have had a few of these where the white rail that the tray gears couple with get "dry" and dirty causing some bad noise when the bins move. Clean the...
  3. Replies
    5
    Views
    207

    [Jamming] Re: CFU AM1 Adv C 5560

    Tried new pick up assemblies, noticed the vert rollers were badly gummed up for some reason on those two assemblies. Suspect the type of paper they run through those trays do not like the new style...
  4. Thread: IR ADVANCE 5560

    by roho
    Replies
    1
    Views
    82

    Re: IR ADVANCE 5560

    Start with a freshly loaded UFR driver on a laptop and try printing using a crossover cable. If the print conditions are normal and all options available then you know it is the driver. Start there...
  5. Replies
    5
    Views
    207

    [Jamming] CFU AM1 Adv C 5560

    Bit of a doozie here. Constant jams from tray 3 and 4, delay jam at ps 76, code 0115. I have swapped pick up units, tried the CFU controller and wiring harness. I am starting to think it isn't the...
  6. Replies
    1
    Views
    161

    Re: CanonIRA C 250IF Error code E602- 1111

    HDD error. You can try reloading FW, or a new disk. If you can reach service mode then probably FW alone will work, but I usually replace the entire HDD and start from scratch.
  7. Replies
    35
    Views
    3,868

    Re: IRC 5250 is there level 3?

    Level 4 is only for levitating the device in mid air. Takes much training and concentration..........
  8. Replies
    5
    Views
    372

    [Misc] Re: iR-ADV 8205 image distortion

    Replace the ap kit as a assembly. I have had this as well, and the gears may turn individually when somewhat disassembled, assuming that's what you did to lube it. Lube won't work, order the entire...
  9. Replies
    28
    Views
    1,589

    Re: C.I.P.'s (Customer Induced Problems)

    Canon CLCs had a transfer drum, and used static to adhere the page to it while transfer was happening. A jam occurred and the key op thought the page was stuck to the drum. When she finally removed...
  10. Thread: blur and bold

    by roho
    Replies
    6
    Views
    285

    [CQ] Re: blur and bold

    Is the blur on the lead edge? Try both corona assemblies.
  11. Replies
    3
    Views
    241

    Re: C5045 question regarding sorter bridge unit

    There is a cover on the finisher top front corner, remove it and depress the lever, finisher disconnected. Remove the silver cover and screws at the left side and then a long phillips to remove 2...
  12. Thread: CANON LBP 6310dn

    by roho
    Replies
    5
    Views
    270

    Re: CANON LBP 6310dn

    I trust "compatible" fixing films less then I trust "compatible" toner. Can you switch fusers? See if the problem follows the fuser.
  13. Re: IR ADV 4025 Enlarging and shifting image only on y axis when copying or printing

    Not exactly the same symptoms I once had with this series but it was another strange printout pattern I was getting. In my case it was the engine controller that had to be replaced, there was a...
  14. Thread: Uniflow offline

    by roho
    Replies
    4
    Views
    268

    Re: Uniflow offline

    Clear main controller, MMI.
  15. Thread: IRA4035 Toner

    by roho
    Replies
    3
    Views
    251

    [Misc] Re: IRA4035 Toner

    Hopper assembly has been known to lose gear coupling, replaced a few of these. order a hopper and remove drum, dev, laser.
  16. Thread: Database Errors

    by roho
    Replies
    43
    Views
    2,029

    Re: Database Errors

    Thanks, that actually worked, have been having data errors for days.
  17. Replies
    10
    Views
    515

    Re: ir ADV C3330 fusing issue

    Some devices with fixing film will not properly fuse some kinds of paper, had a huge issue with this model back in the day. Customer had thousands of rough company letterhead and the new at the time...
  18. Replies
    87
    Views
    14,752

    Re: CALLING ALL McGYVER'S

    Back when I worked for the Mothership I had a pushy by the numbers manager who was on a "work with" me one day. Had a faulty corona assembly and I borrowed his fine new Parker and proceeded to take...
  19. Thread: hello

    by roho
    Replies
    2
    Views
    212

    Re: hello

    Looks like you may require new cyan and magenta devs.
  20. Replies
    8
    Views
    496

    Re: Yellow Drum Unit Problem

    Dirty laser leaves a void area, not a streak of the color in question. Change the drum.
  21. Thread: recognize this?

    by roho
    Replies
    28
    Views
    1,888

    Re: recognize this?

    I can remember the first tv commercial explaining fax machines using geese walking from one machine to the other. The spokesman was a 70's sitcom actor who then asked if he could send over linked...
  22. Thread: recognize this?

    by roho
    Replies
    28
    Views
    1,888

    Re: recognize this?

    You must have never worked with some of my old colleagues, some of those clowns would have the paper fall in and not remove the cover to take it out. Nothing like bent door switches, springs to cause...
  23. Replies
    9
    Views
    764

    Re: Green light for American self-repair?

    NO ONE took that guy seriously at all, it was obvious he was full of used color toner, if you catch my drift!!!
  24. Replies
    8
    Views
    682

    Re: Adv6255 slow scanning

    We set everything to PDF compact, see if those settings match.
  25. Thread: recognize this?

    by roho
    Replies
    28
    Views
    1,888

    Re: recognize this?

    Not a Canon door cheat, I still have a pic of them burned in my brain. Wouldn't surprise me if there was a couple kicking around the basement somewhere................
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4