Search:

Type: Posts; User: mikadonovan

Page 1 of 20 1 2 3 4

Search: Search took 0.30 seconds.

  1. Replies
    37
    Views
    1,017

    Re: Mp 9000 random smudge... I'm gone mad!

    I just remembered an issue I had with a C7501 years ago. The machine was experiencing similar quality issues, and it was due to a gigantic ghost turd floating around in the cavity area directly above...
  2. Replies
    65
    Views
    2,043

    Re: Hurricane Florence

    Service manager to broom pusher. Sound like you work for a real dick.
  3. Replies
    37
    Views
    1,017

    Re: Mp 9000 random smudge... I'm gone mad!

    You might try a new charge assembly, kinda looks like a charge problem and you didnt say you replaced it. It doesn't look like a fusing issue,either.
  4. Re: Need RADF DF-3040 Complete (Reposting)

    RICOH DF3040 ARDF Document Feeder - FOR USE IN GESTETNER MPC4501A C4501 C5501 C5501A LANIER LD645CA 655C 645C 655CA RICOH MPC4501 C5501 C4501A C5501A SAVIN C9145 C9155 C9145A C9155A
    Just a note, I...
  5. Replies
    2
    Views
    171

    Re: Swap MP 4000 PCDU unit

    I've done it on occasion with other models. Install and run a print to check for quality. If ok, set developer and you should be good to go
  6. Replies
    6
    Views
    254

    [CQ] Re: red is orange

    On the Ricoh models I work on, usually a good ID sensor cleaning will bring back decent color. Obviously, if the drums/developers are worn they would need replaced.
  7. Re: Looking for feedback on hooking up a mpc401 where there is no access to router..

    I also did this about a year ago, and it works great. No network related calls have been reported.
  8. Replies
    14
    Views
    966

    Re: MPC 3003 Slow Printing

    This may be a shot in the dark, but there are fuser temp and idle settings that effect print speed. Run a non-default smc and see if any of these have been taken out of specs. After re-reading your...
  9. Replies
    18
    Views
    102,949

    Re: Ricoh Error Codes

    Well, since this old thread is resurrected, I use this website as a reference site accessed on my android when I'm in the field. Not a secure site, but it has a lot of documentation, including error...
  10. Replies
    2
    Views
    238

    Re: c4502 c5502 Feedder

    I just use a little piece or 2 of velcro/double sided tape to hold the cover down after the tab breaks off. Works great, looks good.
  11. Replies
    49
    Views
    6,733

    Re: Electronics

    Stealing someone else's post and using it as your own. That's a new low. WTF is wrong with you? Go away douchebag.
  12. Replies
    4
    Views
    329

    Re: C5502 SC682-13

    They called back yesterday with a "photoconductor unit not set" problem. I went ahead and replaced all the pcdu's and brought the old ones in to troubleshoot. The M unit obviously was not the one at...
  13. Thread: work wear

    by mikadonovan
    Replies
    62
    Views
    5,155

    Re: work wear

    And yet you are on a copier forum trying to sell shoes. Hmmmm...
  14. Replies
    4
    Views
    329

    Re: C5502 SC682-13

    I used the table for rfid errors(may be right or wrong), and replaced the magenta pcdu. Since the code was only logged and not shown, next time I return I should have no more of this code on the SMC....
  15. Replies
    4
    Views
    329

    C5502 SC682-13

    Hi, All. I have a new one here. A sc682-13 is a memory chip at the td sensor error, possibly a bad chip on a dev unit. I would guess the suffix of 13 would point towards the offending unit. Can...
  16. Re: Ricoh MP C3002 GRRRRR TAC TAC TAC noise on Warm up

    SP output mode will narrow it down.
  17. Replies
    3
    Views
    251

    Rt 43 compatibility

    Hi All, I hope your day is going well. I am getting ready for an install of several of the 03 series machines. I have been using the trusty old RT43 LCT for years (1075 through the 6001). My question...
  18. Replies
    23
    Views
    1,334

    Re: Real or altered counters

    It's on page U030 Electrical 1 in the parts catalog. Since the 3d parts catalogs suck, I couldnt really tell where its at. Maybe below the IH coil power supply somewhere.
  19. [Misc] Re: Replacing Hard Drive in Ricoh 6501- Need Software Reload or PNP with Initialize?

    And make sure both drives are exactly the same.
  20. Replies
    2
    Views
    204

    Re: Konica Biz Hub C6500

    Might want to ask this on the KM forum.
  21. Replies
    23
    Views
    1,334

    Re: Real or altered counters

    I ran into a preowned pro 907 a while back that had a low electronic meter, but found out the mechanical meter had over 2 mil on it. I purposefully looked for the mech meter because there were some...
  22. Thread: LinkedIn

    by mikadonovan
    Replies
    6
    Views
    914

    Re: LinkedIn

    Linked In for me was a waste of time. Too many worthless spammy emails and nothing but info about people I already have a business relationship with. Oh, and there's this....
    LinkedIn Data Breach:...
  23. Replies
    10
    Views
    545

    [Error Code] Re: SC 572-00 on MP5502

    I dunno, a location would be nice. Maybe you should not have blanked your entire profile.:confused:
  24. Re: Ricoh MP C5503 Pinting Quality with Color Shadows and Not Accurate

    If you have new pcu's installed, clean the laser shields with the blue stick, and run forced line adjustment (c twice, then run a). The magenta development unit looks to have a clump of toner at the...
  25. Replies
    25
    Views
    2,910

    [People] Re: Rise Of Technology

    Heh heh, I read this and actually remember being taught to use a slide rule in high school. I imagine they still work fine, no batteries required.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4