Search:

Type: Posts; User: Hansen88

Page 1 of 10 1 2 3 4

Search: Search took 0.10 seconds; generated 16 minute(s) ago.

  1. Replies
    1
    Views
    202

    MX-3050,saddle stitching and cover mode

    We dont have a unit here with a saddle stitch finnisher to try this out, and the user manual is not real clear. The customer wants to make booklets and have a nice cover on the outside. From the...
  2. Replies
    8
    Views
    462

    Re: Skewed copies on a MX-654N

    Turns out sharp has a bulletin TT-030216_3 on the proper way to remove the flat cable on the scan mother board. If you dont remove it properly it ruins the flat cable and when reinserted into the...
  3. Replies
    8
    Views
    462

    Re: Skewed copies on a MX-654N

    I was reseating connections on the boards in back and I think I damaged one of the flat cables because now the control panel wont light up. Works on a different machine. I have the cable on order....
  4. Replies
    8
    Views
    462

    Re: Skewed copies on a MX-654N

    Cleaned the optics and clean and lube rails. I went through the adjustments.4A scan image distortion good.4B sub scanning distortion good. 4C main scanning direction distortion is where the problem...
  5. Replies
    8
    Views
    462

    Skewed copies on a MX-654N

    Hello, I am getting skewed copies from off the glass and from the doc feeder. It happens from all drawers but I dont think it is anything mechanical. If I do self prints they come out straight. Aslo...
  6. Replies
    9
    Views
    349

    Re: MX-565 scan to email time out problem

    I am not sure what you are trying to tell me. I looked at the set up guide you linked to. It is set up and works with about 5 or less pages being scanned. it is when scanning about8 pages or more...
  7. Replies
    20
    Views
    821

    Re: Sharp FX-18 Finisher problem

    Did you look up the firmware for the 565 machine or did you look up the firmware for the finnisher model?
  8. Replies
    9
    Views
    349

    Re: MX-565 scan to email time out problem

    No email server, it is set up through a gmail acct.
  9. Replies
    9
    Views
    349

    Re: MX-565 scan to email time out problem

    It was at a business now they moved it just a couple blocks down the street at their house. Everything is all the same as it was at the other location where it was working fine according to them....
  10. Replies
    9
    Views
    349

    MX-565 scan to email time out problem

    Hello, customers machine was working fine, then they moved. Now in the new location if they try to scan to email more than 5 pages it times out. I tried increasing the time out but it times out...
  11. Replies
    5
    Views
    508

    Re: MX-6240 POD1_S code

    I got the machine fixed. The power was correct at the circut board but could not get to the other end of the wires with my meter. The control panel also went dead. When I took that apart there were...
  12. Replies
    5
    Views
    508

    Re: MX-6240 POD1_S code

    This machine has kicked my azz. We have a junker but running machine at the shop. I have replaced all the boards,motors ,ect. Everything I could think of-No luck. To make matters worse is this...
  13. How to reset sims back to Factory default

    I am trying to reset sims to factory default. I was told to change the market area to another market, exit sim, reenter and set back to USA. This did not work. I tried restore system settings in the...
  14. Replies
    5
    Views
    508

    Re: MX-6240 POD1_S code

    I dont think it is the fuser. When I try to run the motors in sim mode they do the same thing as when trying to make copy.The motor makes a humming sound like it is bound up but it is not. If I turn...
  15. Replies
    5
    Views
    508

    MX-6240 POD1_S code

    Hello, I hope someone may have seen this problem. The cause of the code is that the exit motor in the exit delivery unit is not turning on. When I activat the motor in the sim mode- POM-F and POM-r...
  16. Replies
    16
    Views
    1,269

    Re: MX-M753N POD_N1 Revisited

    If it does it every time you can in the sim mode turn off the jam sensors and see if it passes paper then. Then you will know if it is a sensor or mechanical problem. I believe it is in the aging sim...
  17. Replies
    1
    Views
    323

    Re: Toshiba eStudio2830c

    The two codes are probably related. Usually what happens is the rear corona block breaks and the charge comb becomes unattatched in the rear side causing those codes. since the black corona feels...
  18. Re: MX-M503N has E6-11 and 2-2 and 2-1 grayed out

    I was going to order the scan control board also but didnt. This customer is only there a limited time so I have not been back yet. I am supposed to go back there Friday. I will let you all know what...
  19. Re: MX-M503N has E6-11 and 2-2 and 2-1 grayed out

    Yeah, I ordered the doc feed cis unit. Have not recieved it yet. Will let you all know if that fixes it.
  20. MX-M503N has E6-11 and 2-2 and 2-1 grayed out

    This was a new customer first time there. I noticed 2-2 and 2-1 were grayed out. I thought maybe they were disabled for some reason,I didnt ask. The e6-11 code says a white level shading problem....
  21. Replies
    11
    Views
    897

    Re: Toshiba e studio Error E062

    On the ES 450-452 type models the snap in guide that is right below the registration roller gets bowed and will cause 062 codes. They came out with a metal bar that taped onto the plastic guide to...
  22. Replies
    7
    Views
    708

    [Misc] Re: how to tell photocopier is new

    Yes,they dont come ready to copy straight out of the box. Also saved you having to throw out big cardboard boxes and a bunch of styrofoam.The machine needs to be assembled, supplies put in,...
  23. Re: Sharp MX M503N fuser web question and 25-2 dev calibration question

    I have seen those collars on the web before. Like you said the new web rollers are not made so you can use the collars. I throw them out and I have not had any problems from not using them.
  24. Replies
    9
    Views
    716

    Re: MX B402SC Duplex Jams are back!!

    I had the problem of the finnisher mounting plate installed wrong. There is not a lot of clearance between the top of the finnisner and the bottom of the scanner unit. If the finn mounting plate is...
  25. Replies
    8
    Views
    631

    Re: MX-503 multi sheet feeding

    I have not been back to customer yet,so nothing new to report. I am thinking maybe its their paper because the machine does not jam,so I dont think it is the sensors,although I will not rule them...
Results 1 to 25 of 240
Page 1 of 10 1 2 3 4