Search:

Type: Posts; User: repn1999

Page 1 of 8 1 2 3 4

Search: Search took 0.14 seconds.

  1. Thread: DADF K1

    by repn1999
    Replies
    1
    Views
    184

    Re: DADF K1

    Sounds to me like something in the doc feeder is knocked out of place causing the machine to think something is in the doc feeder. could be a loose wire or sensor or a misplaced actuator or a bad...
  2. Replies
    4
    Views
    380

    Re: Mx 7090 card reader issues

    I would also suggest turning off the turn panel off while in preheat/sleep mode option. I did see this issue on a couple 7040 machines but it ended up being an issue with the combination of reader...
  3. [Error Code] Re: MX-M365N F2-64 then super light prints, then it's fine

    I would suggest checking to make sure firmware is up to date. Then check to make sure your density sensor in the transfer unit is clean. I am attaching a bulletin for reference. I have had to replace...
  4. Thread: MX-FN27

    by repn1999
    Replies
    7
    Views
    840

    Re: MX-FN27

    Look at this also
  5. Replies
    11
    Views
    15,039

    Re: Sharp MX4101N L4-45 Error Code

    no there is not a way to ignore the error and allow the machine to operate. These fans are a known issue on alot of sharp mfps and have been upgraded at least a couple times by sharp. just replace...
  6. Thread: MX-4141 E7-11

    by repn1999
    Replies
    1
    Views
    314

    Re: MX-4141 E7-11

    run 63-5 shading gamma default for both sides. This will usually fix this issue. Check that firmware is also up to date. You may have to do adjustments using color SIT chart. FYI there is also a...
  7. Replies
    4
    Views
    501

    Re: MX-3610n scanning to network folder

    I would suggest checking the address to see if it is using the Computer name or IP address. After that I would check to make sure you have a local dns server set as primary followed by another...
  8. Re: MXFR41U Security Firmware update for MX2640

    PM me
  9. Replies
    3
    Views
    416

    Re: Sharp MX-M623N Copying/Printing Slow

    Check tray paper type
    Run sim 50-28 setup adj all select all trays.
    Check torque limiter
    Also it is a known issue for paper feed drive units on all dragon model machines to fail for tray1. If you...
  10. Thread: MX-FN27

    by repn1999
    Replies
    7
    Views
    840

    Re: MX-FN27

    have you ran the machine without the finisher. I agree with the prior post, however an older fuser without the brown pressure roller can cause enough curl to cause this issue also, and then gets...
  11. Replies
    15
    Views
    1,203

    Re: Sharp 2610 curly paper

    check your fuser. sharp made a modification in the fuser and changed the pressure roller inside the belt from a orange one to a newer brown one. they changed it on all aries1 virgo1 and polaris...
  12. Replies
    5
    Views
    1,300

    Re: Sharp MX4101 with H2 05 error

    the common causes for this are usually

    dirty heat belt from client not running heavy color on the right paper/setting
    worn heat belt
    paper stuck behind belt blocking thermistor or thermostat...
  13. Replies
    15
    Views
    3,163

    [Error Code] Re: H4-02 on MX-3060/MX-6070/MX-5070

    ALSO....do not remove the fuser with the power on. Phoenix machines use a different type of thermistors that can be electrically damaged if disconnected while powered, causing random H4-XX codes. I...
  14. Replies
    15
    Views
    3,163

    [Error Code] Re: H4-02 on MX-3060/MX-6070/MX-5070

    I would make sure you have a power filter on it and update to latest firmware 7.60. I have also done the dip switch thing and seems to also work but these other 2 items will ensure the machine works...
  15. Replies
    5
    Views
    535

    [Error Code] Re: MX 4141 & F2-65

    There was an firmware update a while back to make the machine less sensitive to toner adding and less prone to present F2 -6X errors. current version is v4.0 If you need firmware message me....
  16. Replies
    15
    Views
    1,844

    Re: Sharp Copiers Stuck in power loop

    I would check WSD port and maybe turn off SNMP as previously stated. The other thing that has not been said is to check to see if the MFPs are connected to a POE switch. IF they are, make sure power...
  17. Replies
    2
    Views
    788

    Re: MXM 754 admin Password

    small dip switch on the board, smaller than the update switch. dont remember which one it is, but one will boot the machine up in what looks like boot mode but will have the password reset option....
  18. Replies
    7
    Views
    1,463

    Re: MX-M904 with flasing power indicator

    DC Power supply most likely. Same symptom happens to Polaris machines and is the same fix....
  19. HP pagewide pro 577dw scanner image position off

    I had to replace a broken scanner unit on a HP pagewide 577dw. I have already entered the scanner barcode in engineering settings. The image scanned are cut off from the top about an inch. Can...
  20. Re: MX-3570 touch doesnt work/works extremely slow

    Job log could be it. If the machine has been around a while mostly before firmware 6.00 I'd say replace the msata ssd. Sharp forgot to enable trim on the ssd so they basically kill themselves with...
  21. Replies
    3
    Views
    543

    Re: MX7040/MX7580 sec transfer belt rips

    I have also seen this when techs don't powder both belts and blades properly.
  22. Thread: mx-m465n

    by repn1999
    Replies
    8
    Views
    718

    [Misc] Re: mx-m465n

    Make sure you are using yellow and 312 steric acid powder on drum AND blade. Clean off old stuff first and use a lot. There is a bulletin on which powders to use fyi.
  23. Replies
    4
    Views
    1,068

    Re: Sharp MX-565N & Mobile hotspots

    I would recommend not connecting directly to a hot spot. I have done this in the past and 2 things happen. First the hotspots usually have a connection timeout to save battery and sometimes they...
  24. Thread: MX-5070 H4-01

    by repn1999
    Replies
    5
    Views
    642

    Re: MX-5070 H4-01

    Make sure the firmware is up to date as well. There was a bulletin for firmware update for h4-xx codes on that series.
  25. Replies
    13
    Views
    1,834

    Re: Sharp MX-2300 with Magenta background.

    I have had to replace the mfp board and pcu board for a similar issue. looked like a blueprint once kind of, jet black background and then a color image printed on top from just a normal word...
Results 1 to 25 of 183
Page 1 of 8 1 2 3 4