Search:

Type: Posts; User: 1stcavvet

Page 1 of 8 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    6
    Views
    159

    [Misc] Re: hp DJ T2500 plotter

    The printhead in the T2500 does not come with inks the printheads you refer to are smaller and inks are in the unit. These inks are bigger cartridges and 3 are on each side of the machine. I do...
  2. Replies
    1
    Views
    164

    [Error Code] Re: HP Designjet 430 Error Lights

    the first 3 lights staying on steady is for the mark encoder either the line on the roll is missing or dirty or the reader is faulty. the lights you get when you press cancel aren't listed. not all...
  3. Replies
    6
    Views
    551

    Re: Designjet 510, service code 86:01

    check lubrication on the rails and check slop in carrier bearings, check for noises as it goes back and forth, GOOD LUCK
  4. Replies
    1
    Views
    231

    [CQ] xerox cplor 560

    I have to replace all the drums and developer units ---can I take everything out vacuum and install everything at once and calibrate and initialize.
  5. Replies
    3
    Views
    338

    [CQ] Re: copystar CS 3550ci

    thanks for the info , feel a little better about the job now
  6. Replies
    3
    Views
    338

    [CQ] copystar CS 3550ci

    I have a color maintanance kit ---3 drums, 3 dv units etc After installing the new dv units on the drums and replacing all 3 units in the machine. there are a few sims for the dv units and another...
  7. Replies
    6
    Views
    382

    [Misc] hp dj 510 plotter

    I need to get new inks for this plotter right now all the colors are # 82---- the black is a # 10 can I put a black 82 in place of the black # 10.???
  8. Replies
    4
    Views
    481

    [Misc] Re: hp CM4540 MFP

    thank you
  9. Replies
    4
    Views
    481

    [Misc] Re: hp CM4540 MFP

    Do you mean the fuse in the fusing unit, if you mean replace the fuse----that's not the problem. it blows the fuse but never resets the count for the fuser. if you mean something else in the fuser...
  10. Replies
    4
    Views
    481

    [Misc] hp CM4540 MFP

    I tried 2 fusers (new rebuilds) and the printer will not reset I waited beyond 500 pgs with both of them. Sometimes they won't reset for 100pgs or so. This last one went 1000 pgs and still says...
  11. Replies
    2
    Views
    523

    Re: Hp laserjet p3015 13.01.00 error

    be sure to put some silocone grease on the rollers in the rear door and check the motion of the paper in the cassette is not rubbing as you feel the rising motion of the paper GOOD LUCK
  12. Replies
    8
    Views
    613

    [Jamming] Re: Sharp mx c3140 ADF jams

    thanx again
  13. Replies
    2
    Views
    410

    [Error Code] Hp designjet 4520 86-01 code

    Customer said it would do this every once and awhile----Of course ----Called me to replace the shredded carriage belt, Put the belt on start it up goes thru initialization and comes back to the...
  14. Replies
    8
    Views
    613

    [Jamming] Re: Sharp mx c3140 ADF jams

    Can you get to the sensor by pulling back the platen cover and get to it from the bottom??? and thank you very much with all the printer solenoids and flags I have to repair I never thought of...
  15. Replies
    8
    Views
    613

    [Jamming] Re: Sharp mx c3140 ADF jams

    no!!! it makes it past the slit glass and sorta crumples up in the throat of the exit. like it's crashing into dead rollers. after that initial jam it'll run like a champ as long as it's not a...
  16. Replies
    8
    Views
    613

    [Jamming] Sharp mx c3140 ADF jams

    The 1st page thru this ADF jams-------stops as it leaves the slit glass to exit, and bunches up. If you remove it and start again the machine will run all day till it's left to sit for awhile again....
  17. Re: Samsung SCX-6545N Lines when scanning through ADF

    The problem is your customers printers are not fusing properly, the toner is coming off as they pass through the feeder. they're using compatable toner that wont stay on the paper or the printers are...
  18. Replies
    3
    Views
    2,088

    secret to seeing new posts

    When I click on new posts I get redirected to What looks like a google search, how do I get to the new threads they're piling up HELP
  19. Replies
    4
    Views
    696

    Re: HP DesignJet Z3200ps 87.10 error

    first couple things I'd check is that the encoder strip is seated in it's mount properly and see if the sensor on the carrier that reads the strip isn't loose or out of position GOOD LUCK
  20. Re: HP Officejet Pro x476dw MFP Duplex unit life

    Is there a reset procedure when you replace it? I just was talking to a guy who installed a new one and never got rid of the duplex unit full message.
  21. Replies
    23
    Views
    2,266

    Re: Mpc4502 wrinkling through fuser

    the rollers aren't straight the further the paper goes to the edges of the fuser the worse it is, check the bearings or where they mount GOOD LUCK
  22. Thread: Kyocera 4035

    by 1stcavvet
    Replies
    5
    Views
    581

    Re: Kyocera 4035

    yes, it's a malfunction reset you'll see it when you get there execute it then turn the machine off and on again---- if you don't see it in 906 look at 960 it's been a while pretty sure it's 906 ...
  23. Thread: Kyocera 4035

    by 1stcavvet
    Replies
    5
    Views
    581

    Re: Kyocera 4035

    try sim 906 to recover good luck
  24. Replies
    1
    Views
    348

    [Misc] Hp laserjet M4555 mfp WON'T COPY

    WON'T COPY, pages go thru feeder and comes up says on the screen copier control disabled. When the screen comes ready The copy square comes on. The fax square never comes on --No fax attached. If...
  25. Replies
    5
    Views
    442

    [CQ] Re: FS-9530DN White Lines

    little ball of fuzz inside the screen of the charger (main charge)
Results 1 to 25 of 194
Page 1 of 8 1 2 3 4