Search:

Type: Posts; User: mojorolla

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Re: MX 4141 ADF scans side 2 as A4 paper instead of 8 1/2 x 11

    SIM 50-28, spf adj is used to adress image loss on both side of scans. Also check the state or your random width sensor in the ADF.


    :)
  2. Replies
    10
    Views
    1,079

    Re: Motors MX-4070

    We have had 1 main motor replacement and 10 motor replacement, 9 of 10 being color.
  3. Replies
    15
    Views
    1,203

    Re: Sharp 2610 curly paper

    Most Sharps have foam roller inserts on the delivery unit white rollers. Over time, the diameter shrinks from wear and severe paper curl can occur.
    Newer Sharps have these removed for exit options...
  4. Replies
    10
    Views
    1,079

    Re: Motors MX-4070

    I dug out some more documentation on this issue. The link at the bottom links to the photos but there are a few common symptoms this issue will create.

    1. F2-6x codes with the toner cart ejected...
  5. Replies
    10
    Views
    1,079

    Re: Motors MX-4070

    I have had this on at least 5 of the new machines (3070-4070) and various other models.
    It boils down to a crap design.
    The previous models had a motor for each color, four motors, four colors. The...
  6. Replies
    4
    Views
    536

    Re: mx-m465 admin password

    This model does not have ROM chips, it has an SD and CF cards. Additionally there is a main board dip switch to reset admin password on this model. Flip the switch, boot the machine right into SIM...
  7. Replies
    3
    Views
    420

    Re: F1-15 with (2) MX-FN17 on MX-M465n

    Look in the error log for FNSP jams or FNMN# errors. The shafts on the paddle assembly are covered in grease, or the assist assembly is out of sync and will need replaced.


    :)
  8. Replies
    5
    Views
    535

    [Error Code] Re: MX 4141 & F2-65

    Check for a clogged toner tube. Generally you will only get F2-6x errors if value is below 73 or above 200.


    :)
  9. Replies
    5
    Views
    1,300

    Re: Sharp MX4101 with H2 05 error

    Check for a cracked fuser lamp. That is 3 generations old and the lamp lead get very brittle over 10 years or so.

    Additionally, the items you listed as replaced are not even remotely related to...
  10. Replies
    3
    Views
    310

    Re: MX-560NT - Any reason not to use?

    If you shake it too much you are just playing with it!


    :)
  11. Thread: MX-FN27

    by mojorolla
    Replies
    7
    Views
    840

    Re: MX-FN27

    This finisher has a few major issues I have run into:

    - FNSP and F1-22 jams and errors. These are known issues and can be resolved by cleaning the one way clutch shafts at the front of the paddle...
  12. Re: MX-M503N has E6-11 and 2-2 and 2-1 grayed out

    Couple things to check:
    - is the DSPF lamp illiminating
    - SIM 63 check the DSPF gain value, if its double digits, CIS is bad
    Also be aware that DSPF control board only supplies voltages to...
  13. Re: Sharp MX M363N copier, scan to email just stopped today - no error message

    The "test" in the webpage is only to verify your server is an SMTP server; that is all. It does not actually relay any mail.
    Go into the Job Log and look at the email scans. If they are in fact...
  14. Replies
    3
    Views
    422

    [Jamming] Re: jam code "fuser"

    Had this on a few Sharps over the years, most recently a 904.
    Replace the fuser lamp. In the last scenario, the lamp is made of 3 filaments, only 2 were illuminating. The usual symptom of this is...
  15. Replies
    4
    Views
    494

    Re: Sharp mx-2630. Smtp port number

    Some of the Aries and Virgo machine require that you log into the webpage to change certain network settings. On these models, SMTP is not accessible through the touch panel.


    :)
  16. Replies
    3
    Views
    554

    Re: MX-M565 Freezing

    This model had a known issue of the machine freezing or becoming unresponsive due to a failing low voltage power supply.
    Also, remove and open the op panel. I had one a few month back that one of...
  17. Replies
    7
    Views
    1,463

    Re: MX-M904 with flasing power indicator

    Unplug the HDD and boot up the machine. If it comes to an E7-03, the HDD is the issue.
    Additionally, you can look at the MFP board itself and look for the illuminated LEDs, I believe this model had...
  18. Replies
    3
    Views
    543

    Re: MX7040/MX7580 sec transfer belt rips

    I agree as this model has a tendency to clog in the waste toner tubes. Also make sure the main, front door is not clogged. I have seen this a few time and you will actually find a METAL auger, metal...
  19. Replies
    10
    Views
    1,272

    Re: Strange Mark on MX-4101N Prints

    Little mustaches, i like it. I always called them little folded staples.
    Remove the IT belt from the frame and clean the internal rolls, especially the 2 on each end. If something gets caught under...
  20. Replies
    8
    Views
    613

    [Jamming] Re: Sharp mx c3140 ADF jams

    Another symptom of the sticking sensor is the lead edge will usually be off. The timing of the sensors control the timing of the scan. If the sensor sticks, the entire image usually shifts towards...
  21. Replies
    8
    Views
    613

    [Jamming] Re: Sharp mx c3140 ADF jams

    If the jam codes are SPPD3 variants, pull the sensor and flip over the plastic bracket it sits in. There is a "dampening pad" under the actuator flag. Over time, this becomes a "why the hell is this...
  22. Replies
    9
    Views
    716

    Re: MX B402SC Duplex Jams are back!!

    Your jam codes are exiting the fuser and being stuck there, and not reaching the duplex entrance sensor, so basically the same jam by a different name.
    Just from those codes, it will exit the fuser...
  23. Re: Change developer unit message on MAC print driver

    This is a common message for all Sharps from certain versions of MAC OS, :Mountain Lion" being the most troublesome. You can fix this by completely removing the current driver and update to the...
  24. [CQ] Re: MX-3570N Prints are grainy, need advice please

    Clean F and R procon sensors
    SIM 61-13, clear target, reboot machine
    SIM 61-11 AUTO CALIBRATION, select MIDDLE and scann sheets.
    You can also run LOW and HIGH for more accurate calibration.


    :)
  25. Replies
    8
    Views
    912

    [Misc] Re: Open tray 2 and add paper

    LMAO...funny story for you all.
    I had a customer that was experiencing lock ups and the machine calling for paper. Pulled the job log and matched in to the error / jam log on the machine using the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4