Search:

Type: Posts; User: Toxic

Page 1 of 6 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    3
    Views
    177

    Re: how to activate the tray on c2060..??

    Just be sure not to change some other dipsw and forget again ;)
  2. Replies
    3
    Views
    177

    Re: how to activate the tray on c2060..??

    You disabled it and forgot how you did that?
    Why you disable tray1 anyway?
  3. Replies
    28
    Views
    698

    Re: Bizhub c252 problem after fuser reset

    I was hoping for some exotic and strange solution to this problem. :)
    I hope you dont get same problem soon again because we all did not figure what is trouble.
  4. Replies
    28
    Views
    698

    Re: Bizhub c252 problem after fuser reset

    I agree,it should code if turn on without fuser.
    I can confirm this machines likes fast fuses,i use some time ago 100mA fast fuses, it have mark "F" (a lots of them for fuser,transfer belt...).
    ...
  5. Replies
    28
    Views
    698

    Re: Bizhub c252 problem after fuser reset

    I have once similar problem with restarting,hanging up in middle of job,turning off... in no specific order,just randomly,sometimes few days without problem, so hard to troubleshot.
    After long time...
  6. Replies
    28
    Views
    698

    Re: Bizhub c252 problem after fuser reset

    In that "sleep" state,can you ping or access over web page to machine?
    If problem apear just after fuser reset i would start from there,remove fuser,check is fuse open circuit,check...
  7. Replies
    28
    Views
    698

    Re: Bizhub c252 problem after fuser reset

    When screen go black how do you recover again,restart on main switch,sub switch ?
    Did you try troublereset just in case?
  8. Thread: Bizhub c253 copy

    by Toxic
    Replies
    4
    Views
    221

    Re: Bizhub c253 copy

    Try to do install procedure for machine like it is new out of the box.
    What happened before this problem or you buy machines with this problem or some other scenario?
  9. Replies
    4
    Views
    294

    Re: C1070 registration swaying.

    Try to disable registration swing and check is there some improvements.
    On C1060l dipsw for this is 36-3
  10. [Misc] Re: C1060 Toner Bottles TN-619, modify to use for C1060L .

    What is difference and how to do modification?
  11. Replies
    11
    Views
    770

    [Error Code] Re: How to re calibrate the developer

    Is developer fresh poured or done 35k like you said before?
    Try to clean od replace tcr sensor (thing with green label).
    If drum are not oem than 150k is maybe too much for him, oem drum can do...
  12. Replies
    11
    Views
    770

    [Error Code] Re: How to re calibrate the developer

    "Calibrating" developer how you name it is running tcr adjustment in service mode but it must be new developer else it could get code like in your situation.
    Have once that error after replaceing...
  13. Re: Dirty print (vertical magenta and cyan lines - about 225mm long) KM BizHub PRO C6

    Try to print test pages from service mode (test patern output mode,patern 53,density 125) ,one by one color only and check is dirt on every color or not.
    Is it every time same lenght of dirt, 225mm?
  14. Replies
    2
    Views
    154

    Re: Clear impression - pro 1200

    Why did you run 92 I/O ?
  15. Replies
    4
    Views
    338

    [Error Code] Re: Insert the correct Imaging Unit

    I dont think firmware will resolve your problem.
  16. Thread: biz 501

    by Toxic
    Replies
    3
    Views
    317

    Re: biz 501

    Did you check/clean/replace charge corona?
    After that check drum,cleaning blade,developing roller...
    It make sense to follow procedure and replace drum,developer,corona... together.
  17. Replies
    11
    Views
    678

    Re: Yello bands on KM c1070

    Lol,that maybe work in some cases with some people.
    I agree that should be normal procedure.
    In my case when developer depleted second time in about 400k i contact my technical support from KM and...
  18. Replies
    11
    Views
    678

    Re: Yello bands on KM c1070

    I have this problem on C1060l with only cyan developer.
    2 times change developer then search for problems and find firmware which solve this problem.
    If i remember good it was GCD-25 firmware
  19. Re: bizhub 750 paper stuck on separation drum claws

    Looks like problem is about humidity,temperature,moisture in paper...
    Did you try some other paper brand ?
  20. Replies
    17
    Views
    1,532

    Re: KM C258 offsetting issue

    When you replaced ITB did you replace transfer roller,just guess...
  21. Replies
    4
    Views
    307

    Re: Di-183 strange problem

    Have similar problem few times on Bizhub 163 and it was bad "start" microswitch.
    Usually when that is problem you can not feel microswitch to click on touch,its like microswitch is not there and if...
  22. Replies
    7
    Views
    454

    Re: Dead control panel bizhub c224e

    @copyman
    Exactly point to my case with this speciific machine i already mention.
    But it was nice to spent some time with nice girl working there and after work,testing machineis working ok...
  23. Replies
    7
    Views
    454

    Re: Dead control panel bizhub c224e

    I agree ,i would consider to change mfpb only if machine is low clicks and very good condition,better to sell new one,if they dont do much prints and not demanding C227 can do the job.
    About...
  24. Re: [PHOTO] Magenta and cyan vertical lines on first copy KONIKA MINOLTA C220

    Is it occur on all paper types and weights?
    Toners are original OEM or replacement?
  25. Replies
    4
    Views
    2,335

    Re: C1070 error c3511

    Few days ago on C1060l i have C3511 and 3513 after warming up.
    Replaced fusing temperature sensor/1 (non contact sensor) ,problem solved.
Results 1 to 25 of 126
Page 1 of 6 1 2 3 4