Search:

Type: Posts; User: axyun

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    2
    Views
    80

    Re: WC7120 has error 093-320

    Thanks Detonation. Sounds like a good plan. Frank
  2. Replies
    2
    Views
    80

    WC7120 has error 093-320

    Customer called with fault 093-320 on wc7120. I see that it refers to develper unit drive motor.for collor units. Is it usually one of the drum units

    casing the problem and is it best to swap one...
  3. Re: MP W3601 need upper + lower fuser rollers and cleaning blade

    Thank you Stephen. I will look into it.
  4. MP W3601 need upper + lower fuser rollers and cleaning blade

    Is there anyone who can provide upper(AE01-1122) and pressure(AE02-0148) and cleaning blade(B286-3581) at

    good price. Can pay with paypal or your preference. Frank
  5. Replies
    3
    Views
    216

    Re: C6526 with error C7404

    Thanks JR. Should I assume you are referring to dv unit as dv and drum units are separate on this machine and the C7404
    I believe is referring to y dv unit. Have little experience on this machine...
  6. Replies
    3
    Views
    216

    C6526 with error C7404

    I removed drum + dv unit and cleaned out spillage etc. Did not notice anything obvious with y dv unit. Reinstalled but c7404 still appears.

    Any help is appreciated. Frank
  7. Re: MP2000 cuistomer attempted to change drum and.....

    Had to replace developer and sp2214 and ok now. Thanks to all for your input. Have a great holiday. Frank
  8. MP2000 cuistomer attempted to change drum and.....

    Customer attempted to change drum on MP2000 and now has blanks. Got call today. Is it most likely charge roller issue or developer issue?
    I guess i should speak with boss who did it to see if i can...
  9. Re: Bizhub C360 "No animation " message aand not copying or printing

    thanks to all. reset stopprint with stop 01 stop 0C and printing and copying now. I did not see consumable at life end but close . Frank
  10. Re: I don't receive emails when there are responses to my post

    Ok. Thank you Aneurism
  11. Re: Bizhub C360 "No animation " message aand not copying or printing

    Rhank you Copier Addict. i did not see any message to change anything. Also why would computer say machine is offline when customer tries

    to print. I would think it would say something needs to be...
  12. Replies
    4
    Views
    359

    Re: MPC4000 gets sc700 + sc701 after warmup

    It turned out to be the the timing pulley with a cracked gear. It was unable to turn the pickup cam. Temporarily glued it and ordered part. Working for now.Frank
  13. Bizhub C360 "No animation " message aand not copying or printing

    a message "No animation guide data available. Contact your administrator."

    I understand that that refers to the movie data used to show customer hot to remove jams and such. I would not care but...
  14. Replies
    4
    Views
    359

    Re: MPC4000 gets sc700 + sc701 after warmup

    Thank ou Slimslob. I'll post results once I am able toschedule and check mout.Frank
  15. I don't receive emails when there are responses to my post

    I have not been receiving emails when someone has responded to my post. I always got them before though it would be first response after my post. Do I need to

    do something to correct this. I am...
  16. Re: Estudio 356 with MR3022 message Place doc reader in down position

    The original detect actuator was activated though no paper was there. I did not notice that it was not in position as it was not obvious and was concentrating on potential problem with radf position...
  17. Re: bizhub C360 with "document size cannot be detected etc

    Replaced ps14 actuator and spring and adf is working. However there has been a message "No animation guide data available. Contact your administrator."

    I understand that that refers to the movie...
  18. Replies
    4
    Views
    359

    MPC4000 gets sc700 + sc701 after warmup

    MPC4000 with error SC700 + SC701 after warmup . When it does go into ready it does not detect document. Is this usually one of the orig. stopper home position. sensor or Pickup roller hp sensor? This...
  19. Re: Estudio 356 with MR3022 message Place doc reader in down position

    I am almost certain I did not disconnect while machine was on as I am aware it
    could cause problem a board on some machines.

    I was thinking about this logically and I assume as on all machines...
  20. Estudio 356 with MR3022 message Place doc reader in down position

    Estudio 356 with MR3022 radf. Had just changed drum and cleaning blade and fuser unit due to print quality issues from both units.

    The document feeder was running okay though customer mentioned...
  21. Replies
    6
    Views
    526

    Re: Sharp ARM 257/ U2-40

    I have had u2-40 and f2-02 erors and changing cartridge or chip usually did it on this model type. There are other Sharp MX mosels that would require deveper change on the f2 error. FrANK
  22. Replies
    2
    Views
    338

    Re: Mx-M264N with ERR failed to expand ARM8 prg

    Thank you Danceswrabbit. That is very helpful. I will try to obtain an sd card with the data on it already or get on and try to obtain the data and method used
    to download onto sd card. I have...
  23. Replies
    2
    Views
    338

    Mx-M264N with ERR failed to expand ARM8 prg

    Have ERR Failed to Expand ARM9 PRG Could someone please explain in simplest terms what i need to do.
    From what i understand the SD card needs to be changed and firmware upgraded. I have been...
  24. Replies
    2
    Views
    373

    Re: Docucolor 700 with error 010-326

    When I arrived at machine there was a fault code 010-119. I reset the value to 0 on the specified nvm address . When I turned on machine got 010-326

    Customerhad couple of good fuser units. I...
  25. Replies
    2
    Views
    431

    Re: WC7225 with fault codes snet by customer

    Thank you Exok. I have not heard from customer since my last post and my PM to you. Evidently, it was something the customer was able to work

    out nimself or with Xerox guy he was corresponding...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4