Search:

Type: Posts; User: Woxner

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Re: Konica Minolta bizhub C350 - Scratched image

    adjust fuser speed. the paper is buckling as it starts in fuser. it was made to do full color copies. if fuser is old may need to be replaced. i would go too high with temp adj
  2. Replies
    15
    Views
    457

    Re: C224 orange light flashing

    Root Cause
    1. Poor connection or failure of memory module mounted on MFP board.
    2. A failed HDD.
    3. Firmware bug.
    4. Poor connection or failed Interface Cable. Also check these
  3. Replies
    15
    Views
    457

    Re: C224 orange light flashing

    Do a new release on the belt and fuser. Even though set to no stop.
  4. Replies
    12
    Views
    571

    Re: swapping image unit bizhub c452

    a lot of times if cyan went bad could be clogged toner port or blk could be over due. throws the voltage out of range
  5. Replies
    6
    Views
    366

    Re: Liberty HP Manuals gone

    they manuals are still there. its under order parts
  6. Thread: C284e dead

    by Woxner
    Replies
    23
    Views
    1,211

    Re: C284e dead

    go into service and under part isolation turn the tray back on
  7. Replies
    15
    Views
    501

    Re: BH c346e "failure to complete print job"

    use the pcl driver if your going to use the ps dont use xps.
  8. Thread: C364e 16-01

    by Woxner
    Replies
    2
    Views
    203

    Re: C364e 16-01

    how are the one ways. did you sand the shaft. how many miles on the rollers?
  9. Replies
    33
    Views
    1,724

    [Misc] Re: Transfer Roller damaged, damaging Drum Unit

    if you line up the transfer roller and the drum you will see what the wear is. remove the two screws on each end of the transfer roller and remove all but one on each side (black spacer) i have...
  10. Thread: SMB v2 problems

    by Woxner
    Replies
    3
    Views
    439

    [Misc] Re: SMB v2 problems

    there are no plans for support on this model. try ftp
  11. Thread: Bizhub C3851FS

    by Woxner
    Replies
    3
    Views
    227

    Re: Bizhub C3851FS

    no dip switchs to change but you do need proper tray. no need to set size either. there is a bulletim on which tray to use. A4Y6-WY2 this is the proper tray

    the 3350 etc will need firmware and...
  12. Replies
    33
    Views
    1,724

    [Misc] Re: Transfer Roller damaged, damaging Drum Unit

    287 does not have a transfer roller that touchs drum. it touches tranfer belt. if its a 262 363 then remove some of the transfer roller spacers
  13. Replies
    8
    Views
    230

    Re: Bizhub C360 Random Hang up on Logo

    try power supply. 24v may not be kicking in
  14. Replies
    2
    Views
    652

    [Error Code] Re: bizhub c452 c3b07 error

    change the ih coil or relay driver pwb. why are you locked on to one part? could also be fuser or pcrb
  15. Thread: Bizhub 3851FS

    by Woxner
    Replies
    13
    Views
    825

    Re: Bizhub 3851FS

    far as the noise goes there is a lubrication procedure for the finisher shafts. did you do all three pieces of the firmware
  16. Thread: Bizhub 754e

    by Woxner
    Replies
    15
    Views
    796

    Re: Bizhub 754e

    might have blown paper feed board. this happened on earlier series
  17. Replies
    5
    Views
    316

    Re: C3850 light on black only

    have the pull the i/u out and use the wand to clean the laser glass
  18. Replies
    11
    Views
    544

    Re: 284e B&W F/W update gone wrong!

    try doing each piece of firmware one at a time like controller the mfp the finisher etc. if this had bizhub secure sometimes that will do it. but do controller last. had this in 8 series when trying...
  19. Re: KM6500 Drawer 4 &5 How to open with no Power?

    there is open small door next to tray and find small hole. flip the release. its in the manual
  20. Replies
    5
    Views
    347

    Re: FS536 Grippers out of sync.

    i have seen this happoen when working on the machine. not just a customer error. solution is to replace the gripper as a unit. has always worked after replacment
  21. Replies
    11
    Views
    847

    Re: c203 grinding noise

    replace the blk dev clutch
  22. Replies
    9
    Views
    461

    Re: Bizhub C550 color problem

    have youi done the inialize and reset the gradation.
  23. Replies
    2
    Views
    531

    [Jamming] Re: DF-621 W/ reoccuring J66-23 codes

    replace the two feed clutches.
  24. Replies
    10
    Views
    649

    [CQ] Re: Konicaminolta C258 washed out prints

    why care about a demo page. use service mode to test for quility. i have seen this but left it alone because it does not affect customer. dont waste money and time
  25. Replies
    7
    Views
    1,149

    Re: C3bo3. Konica Minolta. Bizhub 558e

    install v1 firmware. this got triggered from a lampcode from the scanner if you look at the history on the print out you will see it.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4