Search:

Type: Posts; User: mojorolla

Page 1 of 20 1 2 3 4

Search: Search took 0.42 seconds.

  1. Re: Sharp MX M363N copier, scan to email just stopped today - no error message

    The "test" in the webpage is only to verify your server is an SMTP server; that is all. It does not actually relay any mail.
    Go into the Job Log and look at the email scans. If they are in fact...
  2. Replies
    3
    Views
    197

    [Jamming] Re: jam code "fuser"

    Had this on a few Sharps over the years, most recently a 904.
    Replace the fuser lamp. In the last scenario, the lamp is made of 3 filaments, only 2 were illuminating. The usual symptom of this is...
  3. Replies
    4
    Views
    259

    Re: Sharp mx-2630. Smtp port number

    Some of the Aries and Virgo machine require that you log into the webpage to change certain network settings. On these models, SMTP is not accessible through the touch panel.


    :)
  4. Replies
    3
    Views
    324

    Re: MX-M565 Freezing

    This model had a known issue of the machine freezing or becoming unresponsive due to a failing low voltage power supply.
    Also, remove and open the op panel. I had one a few month back that one of...
  5. Replies
    7
    Views
    753

    Re: MX-M904 with flasing power indicator

    Unplug the HDD and boot up the machine. If it comes to an E7-03, the HDD is the issue.
    Additionally, you can look at the MFP board itself and look for the illuminated LEDs, I believe this model had...
  6. Replies
    3
    Views
    369

    Re: MX7040/MX7580 sec transfer belt rips

    I agree as this model has a tendency to clog in the waste toner tubes. Also make sure the main, front door is not clogged. I have seen this a few time and you will actually find a METAL auger, metal...
  7. Replies
    10
    Views
    1,049

    Re: Strange Mark on MX-4101N Prints

    Little mustaches, i like it. I always called them little folded staples.
    Remove the IT belt from the frame and clean the internal rolls, especially the 2 on each end. If something gets caught under...
  8. Replies
    8
    Views
    513

    [Jamming] Re: Sharp mx c3140 ADF jams

    Another symptom of the sticking sensor is the lead edge will usually be off. The timing of the sensors control the timing of the scan. If the sensor sticks, the entire image usually shifts towards...
  9. Replies
    8
    Views
    513

    [Jamming] Re: Sharp mx c3140 ADF jams

    If the jam codes are SPPD3 variants, pull the sensor and flip over the plastic bracket it sits in. There is a "dampening pad" under the actuator flag. Over time, this becomes a "why the hell is this...
  10. Replies
    9
    Views
    535

    Re: MX B402SC Duplex Jams are back!!

    Your jam codes are exiting the fuser and being stuck there, and not reaching the duplex entrance sensor, so basically the same jam by a different name.
    Just from those codes, it will exit the fuser...
  11. Re: Change developer unit message on MAC print driver

    This is a common message for all Sharps from certain versions of MAC OS, :Mountain Lion" being the most troublesome. You can fix this by completely removing the current driver and update to the...
  12. [CQ] Re: MX-3570N Prints are grainy, need advice please

    Clean F and R procon sensors
    SIM 61-13, clear target, reboot machine
    SIM 61-11 AUTO CALIBRATION, select MIDDLE and scann sheets.
    You can also run LOW and HIGH for more accurate calibration.


    :)
  13. Replies
    8
    Views
    797

    [Misc] Re: Open tray 2 and add paper

    LMAO...funny story for you all.
    I had a customer that was experiencing lock ups and the machine calling for paper. Pulled the job log and matched in to the error / jam log on the machine using the...
  14. Replies
    5
    Views
    657

    Re: MX-6580 missing pages in scans

    The newest Sharp seems to have this issue on most new ADF, especially the 3070 - 6070 series. I had a machine a few months back that had this issue, it double pulled 3 times after 1000 scans.
    I have...
  15. Replies
    3
    Views
    1,289

    Re: mails from copier

    Yep, need the R.E.D. software from Sharp.


    :)
  16. Replies
    5
    Views
    1,770

    [Misc] Re: MX-B402 SC Distorted display

    This model went through a change in lcd panel a few years back. The display would look like slanted colored lines but achine would boot up.
    The fix was to determine IP address and flash firmware...
  17. Replies
    5
    Views
    1,361

    Re: MX2614 E7-11 Error

    Go into SIM 63 data display. If CCD GAIN value is double digits, CCD needs to be replaced.
    Depending on model, there is an OC and DSPF value....


    :)
  18. Re: full color print only making jam problem in fuser unit.

    So it it only full color and you are getting H5-01...?
    If you are getting H5-01 that means it is MAKING it to the fuser, but not making it out. The full color parts indicates it is sticking in the...
  19. Replies
    9
    Views
    1,447

    Re: MX-4111N Loosing Developer

    Virgo 1 machines pull DV like a dentist pulls teeth....
    Remove the drum unit and check the grounding clip and the corresponding rail. If theses are coated in toner, which is very common in this...
  20. Replies
    4
    Views
    394

    Re: MX 365 user control trouble

    How is the machine set to click pages?
    For example, a double sided ledger copy will click as 4 pages on most boxes. 10 double sided LDG = 40 pages.
    The page limit is pretty straight forward under...
  21. Replies
    2
    Views
    365

    Re: MX-5111 Fuser web stalls

    See this thread....
    http://www.copytechnet.com/forums/sharp/124276-virgo-4111-5141-web-stalls-post582332.html?124276=#post582332


    :)
  22. Re: Sharp MX-5110 with multiple F2-41 codes (cyan dv level 35)

    If you are referring to the 25-1 reading for cyan as reading 35, you have an overtoned situation in the dv unit. These models are notorious for clogged toner tubes and toner dumping. I think it is 3...
  23. Replies
    3
    Views
    581

    Re: 5070, 6070 Image Quality

    50-22
    44-2
    44-6
    44-26
    61-13. reboot, 61-11 for all three modes (light, med and high density along bottom of screen)
    46-74
    Be sure to use good paper for best results.
    A couple other things to...
  24. Replies
    6
    Views
    554

    Re: Unable to print PDFs

    414 is a print emulation error, the driver does not like the file. If there are TIFF images, you can get this error.....


    :)
  25. Replies
    1
    Views
    328

    Re: Sharp tandem tray MX-DE20

    Check these 2 things:
    1. in paper tray settings, are both trays 3 and 4 enabled for print? This is also were auto tray switching is, make sure it is on also.
    2. the print driver. If the print job...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4