Search:

Type: Posts; User: mttech

Page 1 of 5 1 2 3 4

Search: Search took 0.04 seconds.

  1. Re: Sharp MX-C402SC wont restart after going into energy save

    First, make sure the power save and auto power shut off times are different, as that can cause issues. Second, does it wake up when a print job is sent to it? We had a similar problem on a MX-B401 a...
  2. Replies
    3
    Views
    286

    Re: MX-560NT - Any reason not to use?

    You can still use the MX560NT toner. See MFP-TB-1687. Just make sure to give them a good shaking on installation.
  3. Replies
    10
    Views
    1,017

    Re: Office 365 scan to email

    I just noticed on the Sharp IDNC homepage they have a banner that says they are aware of problems scanning with Office 365 and are working on the solution and will update. Not sure if that is good...
  4. Thread: paper feed kits

    by mttech
    Replies
    5
    Views
    738

    Re: paper feed kits

    Yes, it is correct. The parts manual for the MX-B402SC shows these roller numbers. Section 4 Item 34, and Section 5 Items 32 and 34
  5. Replies
    7
    Views
    641

    Re: MXB455w pulling zeroconf IP address

    Disabling mDNS in the network service settings solved my problem. I attached the NIC pages. I don't think I did a very good job of explaining what was going on. Thanks for all the replies.
  6. Replies
    7
    Views
    641

    Re: MXB455w pulling zeroconf IP address

    It will pick up an address with DHCP that is in the 192.xxx.xxx.xxx format. Once the copier is power cycled the address changes to the 169.xxx.xxx.xxx(zeroconf) format. For now I have disabled auto...
  7. Replies
    7
    Views
    641

    Re: MXB455w pulling zeroconf IP address

    The NIC and cable are fine. I got them printing for now by changing the printer IP address in port configuration in the driver to the zeroconf address, but this is just a work around.
  8. Replies
    7
    Views
    641

    MXB455w pulling zeroconf IP address

    I’ve got an MXB455w that is pulling a zeroconfig IP address, such as 169.xxx.xxx.xxx(zeroconf), whenever it is power cycled. It is set for static IP and wired only network. Can someone enlighten me...
  9. Thread: paper feed kits

    by mttech
    Replies
    5
    Views
    738

    Re: paper feed kits

    THE FOLLOWING MODELS CAN USE THE MX-B42DF ROLLER KIT IN PLACE OF PART NUMBERS NROLR1541FCAZ (x2) AND NROLR1542FCAZ:

    MX-2310, MX-2610, MX-3110, MX-3111, MX-3610

    MX-2615, MX-2616, MX-3115,...
  10. [Misc] Re: MX-3100 Stored documents password protected and can't delete

    Try sim 62-11 to delete document filing data. Be aware that this will delete all of the documents. I would recommend to print out the ones you don't want deleted so you can rescan them back.
  11. Replies
    10
    Views
    1,613

    Re: Sharp AR-M160 doc feeder issue

    The ARM160 takes the AR-SP6 feeder and the ARM205 takes the AR-RP6 feeder. They are not interchangeable, learned this the hard way.
  12. Replies
    3
    Views
    535

    [Misc] Re: MX-C301w Noisy Fuser drive

    Most of our noise issues are caused by the upper heat roller bearings. May want to try swapping some fusers around.
  13. Replies
    18
    Views
    2,216

    [Error Code] Re: MX-3050 F2-78 and "sensor calibration fr 06"

    out of curiosity, did you update the firmware? I have had a couple of these machines go into that loop or just lock up when running 46-74, updated the firmware and went through the calibration...
  14. Replies
    6
    Views
    584

    Re: Unable to print PDFs

    Sharp MFPs sometimes have issues with Adobe. One day it will print fine, the next it will start having problems, then it will clear up on its own after a while. I use Foxit, and I have seen posts...
  15. Thread: Scanning to DXF

    by mttech
    Replies
    1
    Views
    318

    Scanning to DXF

    Just wondering if it is possible to scan a document as a DXF file on the MX-3070? I'm assuming no, but if it is possible, I would think either Sharpdesk or OSA are the only way
  16. Replies
    12
    Views
    1,574

    Re: New Sharp model MXB455W

    That is terrible. I guess it proves your top heavy statement. I am not crazy about sending new machines out into the world but sometimes you have no choice. Thanks for the comments and insights.
  17. [Dead] Re: Sharp MX 3070 "Code Error" Updating firmware after replacing Msata and control bo

    You can check to see if the machine originally had a DSK installed by looking for the extra PWB that would have been installed. Check your Installation Manual for exact locations of the extra PWB and...
  18. Replies
    12
    Views
    1,574

    New Sharp model MXB455W

    Just wondering if anybody has placed one of these MXB455W out in the field and your impression of them. We have quite a few of the older A4 machines out that are getting a little long in the tooth. I...
  19. Replies
    5
    Views
    719

    [Misc] Re: Failed - Network error chrome

    On most of the newer machines you can use a USB drive and do these operations at the copier.
  20. Thread: MX-M260...F9-88

    by mttech
    Replies
    5
    Views
    968

    [Error Code] Re: MX-M260...F9-88

    I have seen a corrupted print job cause this code. Does the copier run without the network and fax line plugged in? If so, then plug in your network or fax cable and see if code reappears. Do them...
  21. Replies
    4
    Views
    477

    Re: Mx-3140 ghost jamming

    I think that jam code is trying to tell you that PPD1 is not being reached when feeding out of tray 2. I would check all your PF stations to see if problem is isolated from that tray.
  22. Replies
    2
    Views
    909

    TLS 1.2 on a MX4100N

    I have a customer's IT guy asking if the MX-4100N that they rent from us is able to support TLS 1.2
    The only bulletin I have found about TLS 1.2 is for the newer model machines (MX-3050, 3570 4050...
  23. [Dead] Re: Sharp MX 3070 E7 A7 Error Code. Machine powers off and on now

    I just had to replace the mSATA card on one of these machines the other day

    Before you replace anything though, remove the MFPC cover plate with the machine on, and look for the green lights....
  24. Re: Mx-B402sc misfeeding at registration, and "cleaning transfer belt" message.

    If I remember right there is a photo sensor behind the PS unit. Could have got dirty with the DV spill. Check jam history with sim 22-3 and sensor with sim 30-1.
  25. Replies
    4
    Views
    467

    [Misc] Re: MX-2610 Fusing Belt

    Yes, you now use the MX361FB for the belt. See MFP-TB-515. The new part # cross references to this belt.
Results 1 to 25 of 107
Page 1 of 5 1 2 3 4