Search:

Type: Posts; User: Jeff M.

Page 1 of 5 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    14
    Views
    827

    Re: SMB scanning with Windows 10 issue

    The KM-4050 is in a church day-care center, so I don't think security is a high priority here. I haven't been able to get back there (the office manager was on vacation), that's the reason for my...
  2. Replies
    0
    Views
    19

    Super high volume label printer

    Hi all.

    I've got a customer who prints over 20,000 labels per day. Currently, they're using the Zebra ZT610s. They were using the Zebra ZT410s, but were going through printheads every few...
  3. Replies
    14
    Views
    827

    Re: SMB scanning with Windows 10 issue

    Hi all: Thanks for your replies. Well, I went back yesterday to continue with the M2035 issue, and... it was working! ??? I didn't reboot the computer after changing the SMB setting in the...
  4. Replies
    14
    Views
    827

    SMB scanning with Windows 10 issue

    Hi all.

    I sell Kyocera, and I usually set up SMB scan when the customer wants scanning. Most times it works fine, a few times Kaspersky or McAfee blocks it but can get around that. It seems...
  5. Replies
    10
    Views
    903

    Re: Brother MFC9440 32 error

    I was finally able to get back to the customer today, and yes.... the solenoid was sticking, and that seemed to fix the problem. THANK YOU! I still don't know why the internal prints worked, but...
  6. Replies
    10
    Views
    903

    Re: Brother MFC9440 32 error

    Dickie: With all due respect, I didn't say I wouldn't look at the solenoid. I've actually run into this on a lot of HPs and Kyoceras, so I know it's a common issue. And I said I was going back to...
  7. Replies
    10
    Views
    903

    Re: Brother MFC9440 32 error

    I did get it, and my apologies for taking so long to respond. Thanks, Phil B. and theengel for your responses. I did check for and paper or buildup of toner inside, and it's actually pretty clean. ...
  8. Replies
    10
    Views
    903

    Brother MFC9440 32 error

    Hi all.

    I got a call on this problem today. When you try to print or copy, it gives a 32 error in the display. Past threads have indicated it might be a dirty transfer belt sensor. Funny thing...
  9. Replies
    9
    Views
    3,207

    Re: BROTHER MFC9440/Error 32

    I'll do that.
    Thanks.
    Jeff M.
  10. Replies
    9
    Views
    3,207

    Re: BROTHER MFC9440/Error 32

    Hi all.

    I got a call on this problem today. Funny thing is, it will print an internal print (user setting list, etc) no problem, but when you copy or print, it gives the 32 error. So that would...
  11. Replies
    3
    Views
    269

    Re: Canon iPF785 false paper jam

    Thanks, teckat! It's truly appreciated. Jeff M.
  12. Replies
    3
    Views
    269

    Canon iPF785 false paper jam

    Hi. This is my first foray into Canon's wide format machines. I've been servicing HP Designjets for many years but this is the first Canon I've seen. A new customer called about this one, so I...
  13. Replies
    7
    Views
    1,280

    Re: PF-740(B) tray 3 not lifting properly

    Update: Sure enough, the motor failed again. We replaced it, and all is well. I sincerely appreciate your responses. Merry Christmas to everyone! Jeff M.
  14. Replies
    7
    Views
    1,280

    Re: PF-740(B) tray 3 not lifting properly

    That was my thought. I'm ordering one to have, because I'm sure I'll need it soon. They don't fix themselves, so it's only a matter of time.
    Thanks again for the responses. Jeff M.
  15. Replies
    7
    Views
    1,280

    Re: PF-740(B) tray 3 not lifting properly

    I switched tray 3 and 4 lift motors, and now both are working fine...... ??? No noise, fill both trays up and they lift smoothly. I'm sure it will happen again, but to which tray? To be...
  16. Replies
    7
    Views
    1,280

    Re: PF-740(B) tray 3 not lifting properly

    Thanks, Kyo fan. I'll check it out later today. I looked for torn paper when I was there last time (although I didn't remove the trays) but I don't think there is anything stopping it from lifting,...
  17. Replies
    7
    Views
    1,280

    PF-740(B) tray 3 not lifting properly

    I have a 4501i with 300K on it with a PF-740(B) LCT. When you fill tray 3 (the right hand one) over half full, you can hear it straining to lift and then kicks it out, saying tray 3 cannot be used...
  18. Thread: AK-730

    by Jeff M.
    Replies
    6
    Views
    1,263

    Re: AK-730

    Any luck with finding an AK-730 kit? I bought a used 3500i with a finisher, and some of the pieces are broken. I was able to get most of what I need from the wholesaler, but I need the right hand...
  19. Replies
    2
    Views
    2,587

    Re: MP-301 factory reset?

    Thanks, slimslob. I'll try this. Appreciate your response. Jeff M.
  20. Replies
    2
    Views
    2,587

    MP-301 factory reset?

    I have an MP-301 with a really odd problem. At the customer's office, it will not pick up an IP address by DHCP, nor will it allow a specific assigned address to be recognized on the network. I...
  21. Re: Ricoh MP301SPF Service Mode & saying toner low

    FYI: Had this same problem on a machine with 19K, saying toner low after only a few copies. Customer called, saying green toner release lever was broken, and machine was calling for toner. ...
  22. Replies
    0
    Views
    273

    Need KonMin C25 part

    Looking for a CIS for the BizHub C25, #A2YFPP1100. According to ACM, cannot get scanner alone, only with complete top... over $400. Anyone have one or a junker they will sell the CIS from? Thanks....
  23. Replies
    10
    Views
    1,286

    Re: Parts source for Konica Minolta

    Thanks, appreciate the response. I didn't think of ACM. I'll try them first.
  24. Replies
    10
    Views
    1,286

    Re: Parts source for Konica Minolta

    Normally, that's what I would do, but the local KonMin dealer is somewhat less than helpful to other dealers..... and no, it's not just towards me! Why is Konica Minolta so difficult to get parts...
  25. Replies
    10
    Views
    1,286

    Re: Parts source for Konica Minolta

    Thanks, appreciate it.
Results 1 to 25 of 123
Page 1 of 5 1 2 3 4