Search:

Type: Posts; User: MIKON

Page 1 of 3 1 2 3

Search: Search took 0.13 seconds.

  1. Replies
    18
    Views
    613

    Re: SC 552 AFICIO MP 5500

    If the heater lamps are not connected to the same color on the terminal strip on the rear of the fuser you will get a code. Green to green blue to blue.
  2. Replies
    8
    Views
    357

    Re: RICOH MPC 6OOO FUSER:

    Sc540 is a fuser exit motor error.
    Check for a bind ie. seized bearing .broken bear .bad roller
  3. Replies
    8
    Views
    372

    Re: Pro 8200 Dog earing

    Check foam rollers on exit roller.
  4. Replies
    9
    Views
    1,360

    Re: MP 6002 Keeps going light

    Remove all old developer vacuum developer off mag roller clean mag roller with scotch brite pad install new developer.
  5. Replies
    20
    Views
    2,236

    Re: Ricoh MP 9002 ADF jamming

    Did you remove the assembly like in my pic and remove the pulley off the shaft or did you clean and lube it as stated in the TSB????
  6. Replies
    20
    Views
    2,236

    Re: Ricoh MP 9002 ADF jamming

    Do a search of this forum for mikon.I have a pic posted in a older post of the pulley and shaft you have to clean and lube.I tried to upload it put i couldn't upload it.
  7. Thread: MP6002 sc540-03

    by MIKON
    Replies
    12
    Views
    1,261

    [Error Code] Re: MP6002 sc540-03

    Hope this helps.
    I would try the new part numbers.
  8. Thread: MP6002 sc540-03

    by MIKON
    Replies
    12
    Views
    1,261

    [Error Code] Re: MP6002 sc540-03

    If you installed the new style motor it will short to the housing and continously run you have to change the housing or open up the slot.
  9. Replies
    6
    Views
    458

    Re: Ricoh 6002 DF Jams on mixed sizes only

    Try cleaning shaft and gear where arrow is
  10. Replies
    4
    Views
    403

    Re: Hdd error in mpc8002

    Try formatting with network cable unplugged.
  11. Re: MPC6000 with add black toner msg. New oem toner

    Hope this helps.
  12. Thread: Ricoh MP 6001

    by MIKON
    Replies
    4
    Views
    495

    Re: Ricoh MP 6001

    Is that cross feed or paper feed direction?
  13. Thread: mp7502 sc540-03

    by MIKON
    Replies
    5
    Views
    1,811

    Re: mp7502 sc540-03

    Hope this helps.
  14. Replies
    3
    Views
    1,455

    Re: Mpc6502 .sc442-00

    I.T.B. Lift motor p/n D1361212
  15. Replies
    9
    Views
    821

    Re: MP7500 copiers problem

    Check drum drive flange for the retaining screw , it may have fell out.
  16. Re: Need a quick Firmware update Ricoh mp7001 sp (D062)

    Be careful updating adf you can burn out the adf controller.

    Not sure on the deatails but do some research .
  17. Thread: MP7000 sc547

    by MIKON
    Replies
    4
    Views
    529

    Re: MP7000 sc547

    Check the heat lamp connectors make sure the blue connector is connected to blue terminal and green is connected to green terminal.
  18. Thread: 6502 dog ears

    by MIKON
    Replies
    14
    Views
    1,200

    [CQ] Re: 6502 dog ears

    Check the foam rollers at exit .
  19. Re: Is it normal for ricoh mp65/7500 every 250K Waste toner bottle full ?

    Not normal
    Dump developer
    Clean every bit off dev
    Cylinder.
    Turrn knob and vac until there's nothing left.
  20. Replies
    2
    Views
    312

    Re: MPC 7500/7501 bypass

    Something to check.
    The feed roller is different than the paper trays
    The 1 way bearing should be white.on the bypass...
  21. Replies
    8
    Views
    608

    Re: Large void band on Ricoh MPC6502

    It appears to occur with all color's I would check transfer roller D1366240..........
  22. Thread: Ricoh 8000MP

    by MIKON
    Replies
    2
    Views
    340

    [Jamming] Re: Ricoh 8000MP

    Check this sensor see if sensor flag is hanging up.
  23. Replies
    13
    Views
    749

    Re: Ricoh Aficio MP 6500

    Do you have a blank lead edge . approximately 6mm.?
  24. Re: mp7500, why waste toner bottle easily get full

    I had a mp8001 that started to fill the WTB in 200k after a developer change. I changed developer again and was back to normal. I have been having alot of premature developer failure.
  25. Replies
    4
    Views
    594

    [Misc] Re: MP 6002 Toner Issue

    I would start with a new developer change.
Results 1 to 25 of 56
Page 1 of 3 1 2 3