Search:

Type: Posts; User: TonerMunkeh

Page 1 of 20 1 2 3 4

Search: Search took 0.15 seconds.

  1. Replies
    2
    Views
    129

    Re: MP C8002 Banding

    Usually it's the dev unit itself. You probably don't have to fit a whole new PCDU, just the dev unit on it's own.
  2. Re: Ricoh MP301SPF: Using duplex as default setting in scan

    That one I'm not too sure on. I think there's an setting in scanner SP that's called something like "user info release". If that's disabled it doesn't reset the scan destination, but I don't know if...
  3. Re: Ricoh MP301SPF: Using duplex as default setting in scan

    Yes, use the program features key. It's a diamond with an arrow pointing out of it. Make your settings, then press that key, then program as defaults.
  4. Replies
    16
    Views
    438

    [Misc] Re: Ricoh MP 3045 toner light

    If you cheat the front door and look into the toner hopper, can you see the bottle turning when it's trying to add toner? Which developer did you use?
  5. Replies
    7
    Views
    235

    [Misc] Re: Ricoh MP C3002 paper problem

    Check the discharge teeth on the PTR, some of them may be stuck up.
  6. Replies
    18
    Views
    615

    Re: SC 552 AFICIO MP 5500

    Have any of the thermostats on top of the fuser jumped?
  7. Replies
    10
    Views
    385

    Re: SC544-00 Error at Ricoh MP2553 Copier

    A complete fuser is a bit of a stretch, hot roller, pressure rollers and thermistors definitely, but a whole new fuser?
  8. Replies
    2
    Views
    195

    [Electrical] Re: MP9000 Printer feature disabled

    Could also be someone's enabled the application invalidation for the printer function as if it has a Fiery. 997 is an application selection error.
  9. Replies
    12
    Views
    675

    Re: @remote issue on MPC3004

    Is it a Basil box or Cumin communication? Are you using WIM or SP modes to put the @remote code in?
  10. Replies
    8
    Views
    372

    Re: Pro 8200 Dog earing

    Open the doors and pull out the transport bed. On the left hand side is a guide plate assembly with a solenoid on it. The spring on the solenoid slackens over time and causes dog earing and jam 40.
  11. Replies
    14
    Views
    946

    Re: MPC 3003 Slow Printing

    Unless it's running a solution, switch Java off with SP 5730. That has a dramatic effect on print speed due to more available memory.
  12. Re: Ricoh SP4510, "Set toner cartridge correctly"

    If the customer takes a run-up fitting the drum, then uses a sledgehammer to push it in, the contacts on the sensor boards can be bent. If they are, they can't be reliably straightened, just replace...
  13. Replies
    9
    Views
    318

    Re: Ricoh c820dn SC400 Error

    Compatible toner can cause heavy dusting on this model, leading to poor PCU life and dirty ID sensors.
  14. Replies
    2
    Views
    423

    Re: Pro 8100 dusting

    Comes in the 600K PM kit.
  15. Re: near end toner in ricoh L4160 larg formater

    If you have spares, replace them and see if the machine starts working again. The inks may have a certain timeout they can be installed in the machine before calling for new.
  16. Replies
    7
    Views
    755

    Re: What vsg and vsp stand for_

    Voltage substrate ground and voltage substrate patch.
  17. Replies
    7
    Views
    677

    [Misc] Re: Firmware Updating

    Don't forget to use Internet Exploder when downloading firmware from my-ricoh. It has a yellow bar on the firmware that is newer than the one in the package. Firefox and Chrome don't show this.
  18. Thread: Mpc3001

    by TonerMunkeh
    Replies
    2
    Views
    610

    [Error Code] Re: Mpc3001

    Check the green earthing strap on the side door harness, it could be broken. Also there are two springs either side of the PTR assembly that move it backward and forward, one of those coming off can...
  19. Replies
    28
    Views
    4,834

    Re: Ricoh MP C4000 duplex jam

    I did read the problem carefully, in my experience Jam 024 is caused by that part being warped by the heat of the fuser.
  20. Replies
    28
    Views
    4,834

    Re: Ricoh MP C4000 duplex jam

    Replace D029 4580.
  21. Replies
    13
    Views
    3,149

    The Death of a Venus - A Heartfelt Plea

    Ladies and gentlemen,

    I am sure all you Ricoh trained techs are fully aware of how much of a pain in the arse the Venus is. For those of you who don't know the family names, the Venus is the...
  22. Replies
    4
    Views
    458

    [Misc] Re: SP8300dn Developer unit "Auger"

    I'd just replace the dev unit, if that part of the auger has been shredded the rest of the unit will soon follow.
  23. Thread: SC204

    by TonerMunkeh
    Replies
    4
    Views
    1,003

    [Error Code] Re: SC204

    The door switches can also cause this code.
  24. Replies
    8
    Views
    524

    Re: Pro1357 dev unit lifetime

    According to the service manual there isn't a yield so to speak, it just needs changing when it fails.
  25. Replies
    3
    Views
    444

    Re: Ricoh ProC5100s

    What are the PM counters on? Is all the firmware up to date?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4