Search:

Type: Posts; User: repn1999

Page 1 of 9 1 2 3 4

Search: Search took 0.12 seconds; generated 51 minute(s) ago.

  1. Replies
    5
    Views
    399

    Re: MX-5070v high pitch noise

    replace the belt unit. there are other mods to that unit as well and its easier to get them all at once then make several calls when the other issues do finally come up. work smarter and not harder.
  2. Replies
    18
    Views
    1,599

    [Jamming] Re: MX-3640N Random jam & reeboot

    and i would also do 50-28 setup/adj all trays to confirm its not a timing issue after replacing the sensors
  3. Replies
    18
    Views
    1,599

    [Jamming] Re: MX-3640N Random jam & reeboot

    I have seen this issue before. One time it was the driver pwb being flaky and the other couple times it was the sensors in the vertical path both times in my case being the one before ppd2. I have I...
  4. Re: Turn off maintenance/PM-indication in the display.

    FYI you can skip doing pms to supposedly save money and sure you dont have to replace dv......BUT your toner life will drop to nothing and you will end up spending what you would have saved on the...
  5. Replies
    12
    Views
    725

    Re: MX4141 squeaking from web unit.

    I would suggest replacing all the bearings at rebuild and use krytox xht-s or gpl205 grease on them and all the gear shafts. never getting any noise problems unless its the web motor that needs...
  6. Replies
    14
    Views
    1,559

    Re: sharp mx 453 light prints and copies

    These machines seem to not make the pm cycles using aftermarket drums and toner...Sorry they just dont. First I would check the high voltage output and adjust it to what you get in SIM 8. Next I...
  7. Replies
    5
    Views
    611

    Re: MX5141 fuser wont stop running

    I was going to suggest thermistors. You can check the contact ones with a meter. I believe they should read 30 something ohms under normal just sitting condition. much more than that they are bad.
  8. Replies
    6
    Views
    903

    Re: New memory chips for the MX 4071

    I have been able to read the emmc card using a specific msata reader and external enclosure using raw copy. I have not had the chance to write one and see if it works because I dont have any...
  9. Replies
    2
    Views
    447

    Re: Sharp MX-3070 password changed

    I have had to reset these in the past without a DSK using the normal method of getting a code and contacting the hotline to get it reset. HOWEVER on other models I figured out that if you removed...
  10. Replies
    5
    Views
    471

    Re: Mx3110 vibrating noise

    did you use oem drums and mk kits? check the little gear on the back of the drum unit, and make sure the little tit is not broken on them. also check the transfer belt gear and drive gear to make...
  11. Re: Sharp MX-5070N machine won't change Statatic IP

    Did you guys do a full clone from a previous series machine to this one?
  12. Thread: Doc feeder

    by repn1999
    Replies
    7
    Views
    541

    [Misc] Re: Doc feeder

    would also be helpful to do 50-28 spf adjustment for both sides
  13. Thread: sharp mx-m465

    by repn1999
    Replies
    1
    Views
    249

    Re: sharp mx-m465

    you need to reinstall the watermark firmware using sim 49-3
  14. Thread: mx2640 f2-78

    by repn1999
    Replies
    5
    Views
    419

    [Error Code] Re: mx2640 f2-78

    I assume you stopped the machine and looked at the image on the belt before doing any more troubleshooting to see if the image is screwed up there. I am also assuming you have updated the firmware to...
  15. Replies
    7
    Views
    644

    Re: Sharp MX-2300n quality problem.

    I suspect that issue is from a cleaning blade not cleaning properly. It could be either the primary transfer belt blade or the drum blade for whatever color the latent or ghost image is. If you have...
  16. Thread: sharp mx-m465

    by repn1999
    Replies
    2
    Views
    328

    Re: sharp mx-m465

    reinstall the watermark firmware to resolve SIM 49-5. I have the firmware if you need it and cannot get it on your own.
  17. [Misc] Re: MX-4071 Duplex Paper Guide breaking when closing right door

    I would take a closer look at the delivery unit and ensure all is correctly assembled in that area as well as on the fuser. I believe part of the gate unit butts up against the fuser/delivery unit to...
  18. Replies
    25
    Views
    2,048

    [Jamming] Re: Sharp MX-4141N Phantom Paper Jam

    I would actually check the sensors with a meter. Supply voltage is 5V on them all. the service manual will tell you which sensors read what on the signal line, I have had to replace just about all...
  19. Replies
    4
    Views
    4,549

    Re: MX-3570 - L4-12

    I had to fix an issue similar to this with the same code. Initially I thought it was isolated to the sec trans unit so I replaced it but that didnt fix it. SO testing further I discovered I wasnt...
  20. [Misc] Re: SHARP MXM264 SD CARD faulty, Machine canít boot

    I have the sd card image. if you need it for MXM264 send me a pm
  21. Thread: MX-FN27

    by repn1999
    Replies
    9
    Views
    1,521

    Re: MX-FN27

    I also wanted to add that I have seen curling for another reason like this this on many units with a punch blank...and some with a punch. I have fixed it by moving the mylar out about double on the...
  22. Replies
    7
    Views
    1,487

    [Misc] Re: MX-C311 Firmware

    PM me and I will put it up on my FTP
  23. Replies
    9
    Views
    897

    Re: MX-3116N SD Card Clone File

    hdd raw copy works and it is free and portable...can use on a usb stick. i transfer my files via ftp. set up filezilla on your pc and you can use it to transfer
  24. Replies
    2
    Views
    348

    Re: MX2610N DC Power Supply swap w/mx2640 ??

    I would not do it. Swapping electrical parts between series is not a good idea and will most likely cause wierd issues that are almost impossible to troubleshoot.
  25. Thread: mxm365

    by repn1999
    Replies
    6
    Views
    684

    Re: mxm365

    could be an issue with the build up on the web from running the fuser in 23 plus mode on plain paper. doing this is a double edged sword. i would reset the machine soft switches just to make sure...
Results 1 to 25 of 221
Page 1 of 9 1 2 3 4