Search:

Type: Posts; User: copyman

Page 1 of 20 1 2 3 4

Search: Search took 0.87 seconds.

  1. Replies
    2
    Views
    82

    Re: Minolta c451 with fs 608 finisher

    That finisher wasn't great to begin with. The other finisher for that machine wasn't too bad (FS-519).
    As for your problem it could be so many different things with everything that goes on when...
  2. Replies
    6
    Views
    194

    Re: Probing Questions.... a Lost Art!!

    I try and help customers over the phone all the time. When I have a customer like that I say to them, do you want to try something that will take less than 5 mins? It will save the company $100+....
  3. Replies
    8
    Views
    196

    Re: About forum ads

    PM a member aneurysm. He is the admin
  4. Replies
    10
    Views
    412

    Re: Best way to remove yellowing?

    If they are yellow from the sun or smoke (not as often now a days) than not much can be done to bring them back. They fade throughout the whole plastic. The best I've found to get them looking decent...
  5. Replies
    10
    Views
    324

    Re: Konica Minolta Bizhub C280 for Parts

    The developer units are below the drums, 2 screws and 1 connector each unit. Do you have the service manual? Should be able to find it for free online. The transfer belt is also easy to remove. Step...
  6. Replies
    10
    Views
    324

    Re: Konica Minolta Bizhub C280 for Parts

    Well first off thanks for your honesty. Do you know the history of the machine? Was it working where it came from? That would help a lot to know.

    FYI, many of the motors cannot be turned easily...
  7. Replies
    6
    Views
    331

    Re: Swopping Dev units

    Thanks allan for saving my time. I didn't have a C220 DV unit to put side by side with a c224 which I have plenty laying around. I would of saw they were different and not even asked the question.
  8. Replies
    6
    Views
    331

    Re: Swopping Dev units

    Ok, let me ask it a different way, can you use a C280 dev unit in a C224 and the other way around? Of course having to change the chip/reset pwb from one to the other.

    If anyone has tried it with...
  9. Replies
    8
    Views
    342

    [Misc] Re: Konica Minolta Bizhub C458

    If only when copying and internal pages & prints from computer look fine then check and reseat connectors on the CCD unit
  10. Replies
    10
    Views
    324

    Re: Konica Minolta Bizhub C280 for Parts

    Could be bad but most likely not. Unless of course you take rear covers off and see damage. Not that hard to swing rear cage out and look at the drive motors, etc. If machine got tilted on one end...
  11. [CQ] Re: Bizhub c3850 print control board replaced, will not boot past column screen. Need

    Dude no one here is trying to scare you away. We may seem defensive because so may end users try and pull the wool over our eyes.

    Anyway since you said you did everything by the manual like Wox...
  12. Replies
    10
    Views
    324

    Re: Konica Minolta Bizhub C280 for Parts

    yeah. definitely fire it up and see if it will print the internal test pages. might want to clean it good if toner spilled inside when moved? If pages print good than should be all cosmetic parts...
  13. Replies
    10
    Views
    324

    Re: Konica Minolta Bizhub C280 for Parts

    I have the glass (same as BizHub 223). Getting a C280 trade in next week that I was going to part out. As long as customer don't change their mind and want to keep it as a backup.
  14. Thread: Van ramps?

    by copyman
    Replies
    12
    Views
    1,318

    Re: Van ramps?

    The ramps have been working great! I have even used them a few times right from the van to top level of customers steps. These 12 ft ramps are one of the best "tool" I have bought for the business....
  15. Replies
    5
    Views
    208

    Re: Movie file search

    I always find the Movie file under "special firmware" almost at bottom of list.
  16. Replies
    6
    Views
    331

    Re: Swopping Dev units

    I always wondered if the dev units were same with C224 and C220. Will it work if you swap board/chip?
  17. Re: I always lose the screw of the developing unit

    I use a panasonic electric industrial screwdriver with a dewalt magnetic bit holder. We discussed screwdrivers on this forum before. It's small, balanced, and Lith batt lasts weeks. Great for all...
  18. Replies
    14
    Views
    799

    Re: Happy 4th to all ...

    Yes that flag is part of what makes America great! If you read the history behind that flas as well as Betsy Ross you will see that flag represents the start of abolishing slavery, etc. And changes...
  19. Replies
    14
    Views
    799

    Re: Happy 4th to all ...

    It was the President's speech that inspired to start this thread. I know many members here are like me and love America and I was thinking of them.

    I was seriously trying to be nice to the...
  20. Replies
    13
    Views
    435

    Re: Bizhub 4050 scanner glass clean

    Forgot about that. You are right that is a decent little machine. I've seen so many of them on the wholesaler's list and couldn't believe many of them had meters 300,000+ !!!! When you see a small...
  21. Replies
    13
    Views
    435

    Re: Bizhub 4050 scanner glass clean

    All the ADF's on the small Kon/Min models are junk. C35 & C3350 horrible. What gets me is if they get feedback from the field on how bad a feeder is why would they use same one or same footprint for...
  22. Replies
    9
    Views
    378

    Re: A4 MFP on maintenance recommendations?

    Agree with the others

    If you like this customer talk them into keeping what they have or maybe move up to a C308. If it is the cost of a bigger model you have to show the customer how a bigger...
  23. Replies
    14
    Views
    799

    Happy 4th to all ...

    Happy 4th to all the members on this forum that love the USA like I do. Heck I'll even say happy 4th to the few Liberals on this forum who probably hate America.

    Great to think we will have this...
  24. Replies
    13
    Views
    435

    Re: Bizhub 4050 scanner glass clean

    Yeah Kon/Min probably looked at these as "throw away" models. By time glass is dirty most people have got rid of them or something else happens to machine and just not worth the repair. And of course...
  25. Re: I always lose the screw of the developing unit

    I use a mag screwdriver but some screws & clips just don't hold. After many years of spending as much time trying to find a lost screw in machine as the repair itself took I just assume the screw or...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4