Search:

Type: Posts; User: roho

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    15
    Views
    483

    Re: Advance C250if drum counter

    Correct, so all 4 drums would appear to be viable, usually get around 120 or so, granted light coverage and only a small number in the field. Typically these one fade when they wear down, as opposed...
  2. Replies
    15
    Views
    483

    Re: Advance C250if drum counter

    Don't go by those, I believe if you hit the info key you get a reserved for r&d explanation. Instead go to Copier>Counter>Life as techcat said. The life key is further to the right from Drbl 1. The...
  3. Replies
    60
    Views
    1,856

    Re: Hurricane Florence

    Worried about the constant downpour of rain over the next day or so, hopefully the storm doesn't sit too still. Good Luck!
  4. Replies
    6
    Views
    154

    Re: iR2380 yellow lines

    See it now, would like to see a sequence, but a cleaner likely wouldn't hurt.
  5. Re: Canon ir4025 got dirty print.. please help me..

    Bias or contact issue, classic pattern, check the dev contacts on the dev and machine, check the transfer assembly contacts. There is also a leaf spring that contacts a metal roller which you will...
  6. Replies
    6
    Views
    154

    Re: iR2380 yellow lines

    Drum for sure, if it was a cleaning blade you would see a mix of all the colors and the lines would not be as fine as they are there, classic drum.
  7. Replies
    2,271
    Views
    199,636

    Re: The random thought thread

    I had left the screen door only closed one night and heard a ruckus going on and when I got to the living room I saw my 12 yr old cat on his back legs clawing at the screen at a large racoon on the...
  8. Thread: Canon Ir adv 8205

    by roho
    Replies
    8
    Views
    289

    Re: Canon Ir adv 8205

    Check the primary corona, more likely the cause of that error then the pre transfer.
  9. Replies
    4
    Views
    170

    Re: IRA6265i blank screen

    Yes, possible main controller, however I had this as well and turned out to be the power supply. We had a machine in the back so I took the entire assembly and it worked, I believe there were 2...
  10. Replies
    60
    Views
    1,856

    Re: Hurricane Florence

    Good luck!! Hope you are in land or on higher ground, sounds like the surge and the torrential rain will create havoc. Hurricane Hazel flooded out some areas north of Toronto by the Humber River...
  11. Replies
    60
    Views
    1,856

    Hurricane Florence

    Good Luck to all of you in the South East USA, sounds like it will be one for the books. Cannot imagine what some of you must be going through right now and of course after. Hopefully everyone stays...
  12. Replies
    5
    Views
    293

    Re: CANON IR ADV c 7055

    Take the magenta dev out and take a small folded piece of paper and insert it under the doctor blade. Turn the dev in the proper direction and wiggle the paper slowly and withdraw it. If the voids...
  13. Re: c5255 Spare Parts and Maintenance - What are you keeping?

    Significant improvement on he ITB, and note they are different, as is the upper delivery assembly. Be careful before you swap things out from the first gen. Service call workload began to drop when...
  14. Replies
    1
    Views
    180

    Re: Fax board for advance

    no, completely different units.
  15. Replies
    3
    Views
    175

    Re: 0218 jam code paper deck unit c1

    Gave you a boost, I replaced the manual feed assembly as the guides get worn down as well.
  16. Replies
    1
    Views
    173

    [Misc] pdf timeout error 852

    I have a customer who has been having pdf prints occasionally freeze the 4245. The job will show in the que and the processing light will flash but it will not print, will just stay at that point. I...
  17. Replies
    3
    Views
    175

    0218 jam code paper deck unit c1

    Frequent paper jams on a Irad 8105, from paper deck. I have replaced the pick up feed assembly and M1. No change. The paper will get to the registration guide of the machine and will fall out as soon...
  18. Replies
    39
    Views
    1,206

    [Dead] Re: IRC2380i - Only Green LED but no touch screen

    Quite likely, if the HDD is bad you typically get a error code, either on the home screen if it boots that far or the DOS screen if it doesn't. Sounds like the controller is toast and not even trying...
  19. Replies
    14
    Views
    1,025

    Re: Don'tcha Just Love It??

    Back in the day when they were analog I had one customer phone for a line on the copy. I fixed it and they called back for the same problem two days in a row as they were now using the lined copy as...
  20. Thread: ImageRUNNER 4045

    by roho
    Replies
    1
    Views
    153

    Re: ImageRUNNER 4045

    Try clearing MMI, and then after rebooting, initialize printer, see if that helps.
  21. Replies
    3
    Views
    201

    [Error Code] Re: canon 6220 error E220

    Very old device,so I am going off memory. Check the original scanning lamp, see if it is blown.
  22. Replies
    4
    Views
    255

    [Error Code] Re: Help with C7260 error E000075-0002

    What exactly happened during the power down? Was power interrupted to the device as in a power outage, or power plug being accidentally knocked from the wall? Seems odd the belt would be displaced...
  23. Replies
    2
    Views
    220

    Re: Canon ir adv 8105 bypass tray is not working

    Did you run a P Print and input the values for the multi feeder?
  24. Replies
    3
    Views
    201

    Re: Adv4045 Finisher trouble

    E540 0005 02 Title Tray Lift Motor clock error (Inner Finisher)
    Description At initial rotation, when the Tray Lift Motor rotates and clock
    input is not detected within the specified period of...
  25. Replies
    2
    Views
    242

    [Misc] Re: IR 3230 Blurr Dispaly in Display Panel

    Could be a loose ribbon cable, seen this before. The cable may be able to be refit und used again, if not damaged.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4