Search:

Type: Posts; User: sparkycivic

Page 1 of 5 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    6
    Views
    476

    Re: 8002 fuser not resetting.

    One should never swap EEPROM-equipped items while machine power is on, counts and/or serials will be messed up. It's so tempting when no tools are needed, especially when troubleshooting!
  2. Replies
    3
    Views
    276

    Re: fyi 4002i dv drive

    They always seem good with the explanation... right until I leave.
    seems to be a lot of "after-hours staff" causing problems.
    Kyocera REALLY should label the doors. My label maker uses expensive...
  3. Replies
    3
    Views
    276

    fyi 4002i dv drive

    Here is a little story to enlighten someone in the future who uses the search function.

    I had a machine with complaint of occasional blank output.

    But first a little background;
    There was an...
  4. Replies
    9
    Views
    1,126

    Re: TaskAlfa 3252ci SQUEAKING

    It was the main drum/dv drive assy.
    The waste toner passages/auger are attatched to the front of this drive assy, and a new drive needs the old waste section moved onto it.
    It's actually...
  5. Replies
    9
    Views
    1,126

    Re: TaskAlfa 3252ci SQUEAKING

    our very first installed machine of this style engine (2552ci) had a nasty squeak from the rear of the device during the first two weeks, had to replace the drive pack assembly under warranty. I...
  6. Replies
    4
    Views
    448

    Re: Kyocera M3540idn black dsiplay

    I've had one new out of the box with ribbon cable that had one "finger" peeled back during insertion, and bad colors on display. inspect the ribbon cables for contact deformation.
  7. Replies
    12
    Views
    1,067

    Re: Kyocera 4052ci manual toner door release

    You just need to use a stronger magnet.

    I keep some choice 3.5" HDD actuator magnets around that will yank the secret cover right off, when approached at the upper-half... super handy when...
  8. Re: Kyocera 8000i/1i/2i maintenance kit compatibility

    In a pinch, I've managed to use a dk6720 in a dk6706 application by swapping the chip.
  9. Replies
    10
    Views
    1,029

    Re: Staple waste box is full

    Might a punch hole be caught under the punch unit(optical sensor facing down toward hole waste container) and typo in firmware saying staple?

    I catch myself mixing up staple and hole punch in my...
  10. Replies
    24
    Views
    1,715

    [Misc] Re: Black print in copy mode FS-6025MFP

    swapping eeprom causes code, and u004 to fix. New engine board comes with no eeprom installed, so this is normal engine board "replacement" procedure.

    It WOULD be simpler to just swap working...
  11. Replies
    7
    Views
    657

    Re: CS 5002i loud noise

    I found once the waste toner assembly housing was deformed(incompletely engaged tabs/clasps) at the machine rear end, which caused the gear to only partially engage the waste container gear so that I...
  12. Replies
    24
    Views
    1,715

    [Misc] Re: Black print in copy mode FS-6025MFP

    i had the similar machine (fs-c8520MFP) do exactly this, turned out to be the EEPROM. Had to order new eeprom from Kyo for that machine.
    Keep this in-mind when all else fails... try an eeprom/from...
  13. Replies
    10
    Views
    618

    Re: 4002i internal finisher weird problem

    Isn't the resting position of the new internal finisher tray *down*?
  14. [Error Code] Re: Task alfa CS-6002i S001 on U412 after installing maintenance kit

    platen glass underside, and scanner mirrors need to be clean for this to work.

    tap the lid button and observe the lamp... foggy glass?
    remove glass and use cellphone lamp near CCD, look down at...
  15. Replies
    9
    Views
    870

    [Electrical] Re: 8002i fax system 12 not recognized

    I had a fax stop working, but on a 306ci. it turned out to be the FFC that connects the main board to the expansion bay wasn't seated fully in the connector. this cable is the same across most of the...
  16. Replies
    2
    Views
    536

    Re: Add toner message

    Toner container drive gear/sprocket may have fallen apart. compare neighboring drives to look for missing parts.
  17. Re: TASKalfa 2551ci parts pipe transfer cleaning assy

    Yeah, it looks easy, but it's time consuming and that front plastic assembly is awkward to remove and install. If ONLY they put access holes for those two screws it would be unnecessary to remove the...
  18. Replies
    6
    Views
    907

    [Electrical] Re: Kyocera FS-C8020/8025 Power Supplies

    make sure to use the recent firmware, it changes the sleep behaviour so that main capacitors can't build-up excessive charge via power input spikes.
  19. Re: Kyocera Taskalfa 3252ci background and error codes

    are the waste exits of the drums or belt plugged? We have had a couple of pluggages of the waste conveying auger/chute near the waste bottle and a waste bottle not turning(deformed housing). They...
  20. Replies
    9
    Views
    989

    Re: M6526cdn with error C6000

    C2340 Fuser pressure release motor time-out error.
    "When the fuser pressure release motor is driven, the envelope switch (EVSW) is not detectable for 6s."

    Was that the correct fuser, and is it...
  21. Re: Kyocera Taskalfa 6550ci exit unit motor stalls

    the exit motor is likely stalling because the fuser exit signal wasn't received during the allowed time. the sensor is within the fuser...
  22. Replies
    20
    Views
    3,632

    [Misc] Re: Kyocera Setup Tool

    I always use the setup tool "convert" function. it does the whole batch of what's possible in one step.

    first, export ALL the 917 data to USB from old copier. Certain models won't convert unless...
  23. Replies
    2
    Views
    701

    Re: CS-2551ci C7620 and Magenta streaks

    the C7620 codes are symptomatic of toner being on the belt when none should be present. Any transfer cleaning issues will trigger C7620, but that code is never displayed to the user. Given the track...
  24. Replies
    12
    Views
    1,993

    [CQ] Re: TA-8002 belt run off

    Is the assembly sitting properly on in front of the spring loaded white buttons at the bottom, or on top? Maybe one of the buttons is stuck/busted?
    I always have a hard time getting that assembly to...
  25. Replies
    7
    Views
    2,466

    [Misc] Re: New TASKalfa 13600 Series aka RICOH

    KDAConnect is deprecated. Unfortunately, we must use KDA Central to get any new information or files. It's a terrible design, but it works.

    ... And the link for "production" equipment is Broken...
Results 1 to 25 of 124
Page 1 of 5 1 2 3 4