Search:

Type: Posts; User: Cantechman

Page 1 of 6 1 2 3 4

Search: Search took 0.16 seconds.

  1. Replies
    6
    Views
    434

    Re: C3350 gradation adjutment?

    Did you try cleaning the idc sensors? You have to remove the transfer belt to do it. I have seen several color related issues abd cleaning the idc sensors helped quite a bit.
  2. Thread: Bizhub 25e

    by Cantechman
    Replies
    14
    Views
    667

    Re: Bizhub 25e

    I have never worked on the 240 but I have on the 25e and I can say that I am not a fan. The display and service mode alone is enough to make me want to stay away. I think something like the 4052...
  3. Thread: C558 noise

    by Cantechman
    Replies
    20
    Views
    1,637

    Re: C558 noise

    Does it have a finisher? Remove the middle transport section between the exit section and finisher, turn it over and grease the bushings for the transport rollers in that unit. I had a squeak...
  4. Re: Bizhub C452 doesn't p-rint after Fusing repair,data light blinking,no Demo p-rint

    Try just unplugging the network cable and them turning the machine on and then try internal prints it will at least rule out your network.
  5. Re: Konica Minolta bizhub 25e Toner Empty - No Reset

    This is an old thread but i'm having the same issue. whats is normally done to fix this? I assume you try a another new toner first? If that is the same result then what?
  6. Replies
    10
    Views
    773

    [CQ] Re: Konicaminolta C258 washed out prints

    I have the exact same issue on 2 c308's installed at the same time in the same location. I didn't replace any parts though as test prints in service mode and all print and copy jobs are fine. I...
  7. [Misc] Re: Konica Minolta C3351 Customer is requesting factory reset

    I recently did a total clear on a c3351. Basically it resets it back to factory setting. If you don't need anything special reinstalled you should be ok doing the reset and then turning it on with...
  8. Re: How can I disable a PKI card reader that was previously installed on a 363?

    You may have to clear all data. That will erase all user settings as it if was a new install.
  9. Replies
    8
    Views
    692

    [Misc] Re: Konica Minolta bizhub 501

    I must be one of the few that actually didn't mind the 500-501's, had lots in schools and they worked pretty good considering the use they got, regular maintainence was generally it. I I hate the...
  10. Replies
    1
    Views
    332

    Copitrak terminal on c658

    Has anyone hooked up a Copitrak terminal to a C658 with a 4 pin key counter cable? My machine can only perform one function at a time when the key counter mode is enabled. I have set the "next job...
  11. Replies
    22
    Views
    3,607

    Re: C287 series common squeak locations

    Fixed my issue by changing the duplex motor speed with a special firmware. It slows the motor slightly, not really enough to notice but the noise goes away.
  12. Replies
    0
    Views
    160

    c3850 fs says add toner

    Machine had a c2557 error, I replaced the image unit, error went away. Then it says to add K toner, it detects the cartridge but won't seem to add it. The toner motor works, it has the latest...
  13. Replies
    2
    Views
    524

    Re: Vendor Mode 2 limitations

    I had the issue of a c284e a couple of years ago, took weeks to get it sorted out. Here is a couple things to check that I recorded at the time.

    dip switch 30 bit 5 hex 20 enables multi job...
  14. Replies
    22
    Views
    3,607

    Re: C287 series common squeak locations

    Good idea, I may try and get a audio recording of the noise tomorrow, try the firmware and post both results.
  15. Replies
    22
    Views
    3,607

    Re: C287 series common squeak locations

    Old thread, but has anyone tried this firmware? I have a new install of a c287, it makes a fair amount of noise when doing the second side. Does this work? I was thinking it was a noisy motor.
  16. Replies
    0
    Views
    4

    [Misc] bizhub c308 faded test print

    I have a weird issue. 2 C308's in the same building both have faded demo pages, config pages, font lists. Prints and copies are fine. Just those test prints in the user mode. Any ideas? It's not...
  17. Replies
    11
    Views
    5,753

    Re: New Bizhub C308 error C-9403

    Has the error stayed away? I have the same error now on a week old install of a c308.
  18. Replies
    1
    Views
    347

    C3850 fs fax problem

    Hey guys, got a weird one, it's a new install for the above model. A couple weeks after install they noticed they weren't receiving faxes from one particular place, I disabled ECM and JBIG, tested...
  19. Replies
    15
    Views
    1,196

    Re: C-4520 AFTER FIRMWARE UP....

    Your problem is most likely a dirty color registration sensor. Clean it and the machine should start up fine. Drums do not correspond with specific firmware.
  20. Replies
    3
    Views
    1,511

    Re: TCR Sensor part number

    26na 8804 1 tcr sensor bizhub 500
  21. Replies
    1
    Views
    756

    [Misc] Re: Konica Minolta C5501 Transfer belt

    If you are not a tech I would suggest you find a qualified one. It's not overly complicated, however there are a number of small steps that would be too hard to describe without you having and...
  22. [Jamming] Re: minolta cspro ep3000 crampled paper at fuser unit

    You have to go into service mode and look for the paper tray setting and change the setting of the tray there to correspond with the tray's physical setup.
  23. Replies
    4
    Views
    1,061

    Re: Minolta CF-9001, prehistoric problem.....

    Yeah I knew it wasn't directly the same as your problem, but I was just throwing it out there where this machine is so old, I don't expect you'll get a lot of responses.
  24. Replies
    4
    Views
    1,061

    Re: Minolta CF-9001, prehistoric problem.....

    I don't know if this is applies to what your looking for but I found this.. I don't know what SOS-2 is ...start of scan maybe?

    1. The control panel locks up in the SOS-2 mode

    SOLUTION: Verify...
  25. Replies
    6
    Views
    1,320

    Re: Minolta 5000

    That wll do nothing to fix that problem
Results 1 to 25 of 136
Page 1 of 6 1 2 3 4