Search:

Type: Posts; User: Scottb

Page 1 of 9 1 2 3 4

Search: Search took 0.16 seconds.

  1. Replies
    14
    Views
    1,386

    Re: cs3051...oh boy is this a good one

    Before yesterday I would have said yes to the wiring damage being resolved, but when we found two harnesses damaged I am no longer certain. I have a couple of things to order to make sure that the DF...
  2. Replies
    14
    Views
    1,386

    Re: cs3051...oh boy is this a good one

    This is for those that helped and have been following on.... The fix was 302LC94390 memory... oh and yes there were two other wiring harnesses that were chewed on that we missed not once but...
  3. Thread: F60A codes

    by Scottb
    Replies
    11
    Views
    1,041

    Re: F60A codes

    Thanks guys! I appreciate the information
  4. Replies
    1
    Views
    476

    Re: Canon Imagerunner 2200 ADF pad

    try FL2-0963-010 it is similar enough to work best that I remember
  5. Thread: F60A codes

    by Scottb
    Replies
    11
    Views
    1,041

    F60A codes

    is anyone else getting these F60A codes on the 02 and 03 machines during the early morning, and does anyone know what is causing this
  6. Replies
    2
    Views
    241

    [Misc] Re: 5501i Not waking out of sleep mode

    i had one recently, but it was the main pwb.... but you may try the HDD
  7. Replies
    8
    Views
    303

    Re: E0075 0002 error code on c5051

    Bad or dirty sensor may be your culprit in that case...if it throws the code right off
  8. Replies
    8
    Views
    303

    Re: E0075 0002 error code on c5051

    Transfer belt error
  9. Replies
    5
    Views
    306

    Re: Canon IRA C2225 Will Not Receive Faxes

    often if it will send and not receive the copier has been moved to be cleaned behind it...and the phone line is plugged into the wrong hole.

    other than that it may be an incoming voltage...
  10. Thread: C2020 no power

    by Scottb
    Replies
    3
    Views
    352

    Re: C2020 no power

    I would also make sure that the breaker to that plug isnt tripped
  11. Thread: do feed issue

    by Scottb
    Replies
    1
    Views
    201

    Re: do feed issue

    one way bearing going out?
  12. Replies
    10
    Views
    690

    Re: Falcon 2 Open Drawer 1 message

    if its not the lift motor, I would check the connector that the feed unit plugs into on the back of the frame.
  13. Replies
    4
    Views
    460

    Re: Transfer belt error

    This may help
  14. Replies
    4
    Views
    785

    Re: M3540 Jam code 0101

    If I remember correctly mine was the engine pwb...but to be honest I must have been covered up not to post the fix...just incase I needed the gentle reminder
  15. Replies
    8
    Views
    445

    Re: UTAX 3060i Dying

    there is a code that goes along with this message
  16. Replies
    5
    Views
    359

    Re: CS 5053ci Timing out while pdf printing

    The following fixed my issue

    Advanced tab>Print as image

    Properties Tab>Imaging>Color Selection>Text and Graphics

    Thanks for the help guys.
  17. Thread: CS 5501

    by Scottb
    Replies
    5
    Views
    367

    Re: CS 5501

    I took a spare laser (from a donor machine) with me and swapped it out, with the intention of bringing the old one back and cleaning the poly mirrors...but it fell off the copier and hit the concrete...
  18. Replies
    22
    Views
    1,822

    Re: kyocera CS3011I 0501 jam error HELP

    302KV44041 fig 23 could be one of these is a little rusty...
  19. Thread: CS 5501

    by Scottb
    Replies
    5
    Views
    367

    CS 5501

    This guy has 3+ million copies, and has developed a light edge on both prints and copies. The first tech replaced the DV and Drum with both new units, and the transfer assy with an known good one. I...
  20. Replies
    5
    Views
    359

    CS 5053ci Timing out while pdf printing

    The test print was a 9 page pdf and after sending about 11% to the copier it hangs up. It prints word docs just like its supposed to. This is a new install with latest firmware and drivers. Has...
  21. Replies
    4
    Views
    361

    [Misc] Re: Canon iR3245 - Copy issue

    are the originals being pulled from the document feeder or is it being scanned from the glass or a print from the computer, and have you checked the cassette side guides
  22. Replies
    8
    Views
    699

    Re: Kyocera Taskalfa 4551ci / ghost printing

    if its on the back of a single sided copy I would check the fuser first...
  23. Replies
    1
    Views
    347

    Re: KFS Auto Toner Ordering Heads Up

    We use subgroups... Like the county school district then we name each copier with the school name, location and Tk number so our lady who fills the toner orders knows which school and toner type
  24. Replies
    6
    Views
    600

    Re: TA8001i Exit rollers running in reverse

    you're either getting a duplex non arrival jam or a stationary jam the full jam code would be more helpful....but in order for the paper to enter the duplex section the exit section will feed the...
  25. Replies
    5
    Views
    330

    [Misc] Re: IRC2880 touch panel calibration change

    I would try this

    FK2-0329-000
    1

    ANALOG TOUCH PANEL UNIT
Results 1 to 25 of 201
Page 1 of 9 1 2 3 4