Search:

Type: Posts; User: sparkycivic

Page 1 of 5 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    6
    Views
    668

    [Electrical] Re: Kyocera FS-C8020/8025 Power Supplies

    make sure to use the recent firmware, it changes the sleep behaviour so that main capacitors can't build-up excessive charge via power input spikes.
  2. Re: Kyocera Taskalfa 3252ci background and error codes

    are the waste exits of the drums or belt plugged? We have had a couple of pluggages of the waste conveying auger/chute near the waste bottle and a waste bottle not turning(deformed housing). They...
  3. Replies
    7
    Views
    475

    Re: M6526cdn with error C6000

    C2340 Fuser pressure release motor time-out error.
    "When the fuser pressure release motor is driven, the envelope switch (EVSW) is not detectable for 6s."

    Was that the correct fuser, and is it...
  4. Re: Kyocera Taskalfa 6550ci exit unit motor stalls

    the exit motor is likely stalling because the fuser exit signal wasn't received during the allowed time. the sensor is within the fuser...
  5. Replies
    20
    Views
    2,704

    [Misc] Re: Kyocera Setup Tool

    I always use the setup tool "convert" function. it does the whole batch of what's possible in one step.

    first, export ALL the 917 data to USB from old copier. Certain models won't convert unless...
  6. Replies
    2
    Views
    443

    Re: CS-2551ci C7620 and Magenta streaks

    the C7620 codes are symptomatic of toner being on the belt when none should be present. Any transfer cleaning issues will trigger C7620, but that code is never displayed to the user. Given the track...
  7. Replies
    12
    Views
    1,715

    [CQ] Re: TA-8002 belt run off

    Is the assembly sitting properly on in front of the spring loaded white buttons at the bottom, or on top? Maybe one of the buttons is stuck/busted?
    I always have a hard time getting that assembly to...
  8. Replies
    7
    Views
    1,515

    [Misc] Re: New TASKalfa 13600 Series aka RICOH

    KDAConnect is deprecated. Unfortunately, we must use KDA Central to get any new information or files. It's a terrible design, but it works.

    ... And the link for "production" equipment is Broken...
  9. Replies
    7
    Views
    1,755

    [Misc] Re: Kyocera Fleet Services

    which models are affected?
  10. Replies
    2
    Views
    1,381

    [Error Code] Re: Ram disk error

    1: update driver
    2: try spooler setting on/off
    3: try ram disk setting on/off combinations in driver and machine.
    That's my usual routine for this type of call
  11. Replies
    8
    Views
    1,075

    Re: TASKalfa 2551ci ticking cracking noise

    for all our 2550's and 2551's, creaking noises while preparing/post print is expected. Not sure where it comes from, but I suspect fuser or developer.
  12. Replies
    14
    Views
    3,079

    Re: DF-7120 J6511

    What was the setting before? Do you adjust these beyond default "0" values when installing or was it shipped that way?
  13. Replies
    5
    Views
    525

    Re: ECOYSYS 6525

    this particular model is particularly prone to this distortion issue.
    a modification exists that adds ramps to the path at the glass, but to be honest, adjusting the hinge height and also checking...
  14. Re: TASKalfa 3050Ci Service Mode Login not working

    Is Job Accounting turned on? Need to login first before svc mode will work.

    otherwise, maybe try starting copier with door open
  15. Replies
    11
    Views
    823

    Re: Kyocera fs 6525

    fs-6525 has no u906. "reset disabled unit" on models like this, is accomplished as per Black Cat's menu instructions.

    The finisher probably had a stapler jam or belt sensor error, and therefore...
  16. Replies
    2
    Views
    359

    [Electrical] Re: TaskAlfa 3252ci non responsive screen

    had one where some grit got between the bezel and the screen. try run a business card under the bezel all around, reboot copier. or disassemble the covers and inspect-if you're like that
  17. Thread: FS 6525

    by sparkycivic
    Replies
    2
    Views
    300

    Re: FS 6525

    is the 5v supply working? it Could have been waiting for a chance to die
  18. Replies
    8
    Views
    797

    Re: kfs frustrating lately

    what even is the point-of-contact for it? Usually web apps have a link to contact the dev team or similar, but I see none for KFS.
  19. Replies
    8
    Views
    797

    kfs frustrating lately

    Anybody else notice KFS having great difficulty the last few days with pulling reports, pulling maintenance mode info, or getting any info from machines?

    I've got several machines that I simply...
  20. Replies
    9
    Views
    1,279

    [CQ] Re: 2551ci transfer belt auger backing up

    schedule lots of time to tear apart the entire front and LHS of the machine for replacing that "parts pipe transfer cleaning assy".

    In hindsight of having done this a few times - a few...
  21. Replies
    6
    Views
    642

    Re: TaskAlpha 2551ci & 2550ci fuser

    That's too bad, it was nice that the 255 and 8525 could both work with the same fk-896.
  22. Replies
    6
    Views
    652

    Re: Kyocera Mita ECOSYS m3540idn fuser

    I feel lucky, we don't have any of those in our fleet
  23. Replies
    12
    Views
    1,537

    Re: Taskalfa 2551 Large Black line

    black drum/charger? black dv?
    try swap drum/charger to another color position
  24. Replies
    2
    Views
    389

    Re: bug in 306ci?

    The 306ci lacks the functionality you speak-of
  25. Replies
    2
    Views
    389

    bug in 306ci?

    Here's a fun exercise;
    set your 306ci for default platen original size to "letter".-this is how we have been defaulting all our stuff forever
    place any original on the platen.
    choose "legal" size...
Results 1 to 25 of 106
Page 1 of 5 1 2 3 4