Search:

Type: Posts; User: Gift

Page 1 of 20 1 2 3 4

Search: Search took 0.18 seconds.

  1. Thread: 4430L error

    by Gift
    Replies
    2
    Views
    256

    Re: 4430L error

    perhaps a dial tone detection? USR bit sw22 / bit 0->0
  2. Replies
    7
    Views
    425

    Re: Ricoh MP301 bad hard drive

    HDD was indeed an option and not required for most functions. I think some direct print-from or scan-to USB might not work without HDD option, perhaps Airprint, too but everything else will do it's...
  3. Replies
    7
    Views
    484

    Re: Bizhub C659 / C258 Panel Freeze

    Might be true but usually there are no major issues with mass production fw releases since these has been tested thanks to the maintanance releases or special fw (wich improvements mostly went into...
  4. Replies
    1
    Views
    303

    Re: bizhub C35 firmware

    Good introduction.... :rolleyes:
  5. Replies
    7
    Views
    484

    Re: Bizhub C659 / C258 Panel Freeze

    We handle it that way, too. Unfortunately this error was introduced (not fixed) with a new firmware (but does affect a little percentage of the MFP's in certain enviroments) so sometimes you don't...
  6. Replies
    38
    Views
    98,333

    Re: MPC2500 firmware upgrade procedure

    You probably must have good connections to Japan in order to get these. P2P is all we get.
  7. Replies
    7
    Views
    484

    Re: Bizhub C659 / C258 Panel Freeze

    Got some new input - it's probably a firmware issue introduced with g00-u8
  8. Replies
    7
    Views
    484

    Bizhub C659 / C258 Panel Freeze

    Hi, I do have a customer using a pretty brand new C659 (~3 month) and have an issue that the machine/operation panel "freezes" about one time in one or two weeks. It doesn't stuck displaying the...
  9. Replies
    8
    Views
    397

    Re: Calculate Cost per Copy on used Machines

    Calculation tools/excel sheets are usually too optimistic, even for brand new units. There are plenty things so consider starting with the "type" of customers and how "quality demanding" they are....
  10. Replies
    7
    Views
    418

    Re: Dead control panel bizhub c224e

    I prefer the Cxx4e engine since the drums last much longer so in average I get less calls. Had electrical/board/hdd/ssd issues with both series every now and then (mostly no big deals).
  11. Replies
    16
    Views
    902

    [Misc] Re: MPC3502 VOIP Not Receiving Faxes

    Most of VoIP tweaks affects both tx and rx so this might be another issue. You might tweak the cable - modify it so just the two middle wires inside the RJ11 connector are wired to the connector on...
  12. Replies
    17
    Views
    1,460

    Re: KM C258 offsetting issue

    This ghosting image looks like the charge or grounding isn't evenly spreaded among the surface after the erasing so the OPC surface isn't properly prepared for processing, that's why you noticed...
  13. Re: How to supress PM Part messages at end unser computers

    Thanks for sharing, definetly something I have to ckeck out.
  14. Replies
    5
    Views
    557

    Re: SPC840dn PCDU mods

    Correct - you need to swap the Toner density sensor and the front cover won't fit without cutting away some plastic or leave it away. You also should use manual new unit set SP for initializing the...
  15. Re: How to supress PM Part messages at end unser computers

    That's happening with all models, e.g. Cxx0, Cxx4, Cxx8 series... It's also a "general" topic that affects probably all brands.

    I know about dip switches for supressing the messages on the...
  16. Replies
    12
    Views
    906

    [Misc] Re: Ricoh MPC 3503 won't login IT help

    If you can get in touch with a prommer you can format/overwrite the NV ram with "FF" data - it's as good as a new set (wich isn't that expensive anymore though)
  17. How to supress PM Part messages at end unser computers

    Hey ho,

    is there a reliable way to avoid pop ups within newer MacOS/Windows enviroments like "low toner" or "drum unit replace".
    I think this is pretty lame for service contracts because most...
  18. Replies
    12
    Views
    1,291

    Re: Bizhub 4 non e series Control panel

    perhaps you need to request it at your KM product support contact
  19. Replies
    11
    Views
    10,601

    [Error Code] Re: SC 520-00 (MP 2501sp)

    This unit is a total downgrade engine- and construction wise compared to the MP2000 (and that wasn't really my favourite, too^^) - luckily I was able to concinve the sales people to avoid selling...
  20. Replies
    68
    Views
    3,245

    Re: Hurricane Florence

    hang in there guys
  21. Replies
    5
    Views
    328

    Re: Bizhub 222 replacement digitizer/touchscreen

    We ended up trying it and to make a long story short: The 3rd party digitizer for the BH250 fits 100%, yay!!!
  22. Replies
    19
    Views
    721

    Re: Ricoh MP C3002 Using excessive Yelow Toner

    Just share the SMC logging data lists with us (black out the S/N). In case the values are OK there might be a pile of toner in the rear/drive area of the MFP lol^^
  23. Replies
    5
    Views
    468

    Re: MP3554 Login Password

    Newer mfp's force us to set custom user/password combination during first time installation, of course we stick with the usual ones but you'll never know if you see a MFP that has been installed by...
  24. Replies
    19
    Views
    721

    Re: Ricoh MP C3002 Using excessive Yelow Toner

    Ist the toner relly empty when the machine says "toner end"? If not, you might have some sort of toner pump/supply issue. If yes, you shold check the logging data smc lists / perhaps post them here...
  25. Thread: C203 line issues

    by Gift
    Replies
    19
    Views
    880

    Re: C203 line issues

    Running marks and general wear on the transfer belt might also show line-artefacts on half tones visible within all colors
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4