Search:

Type: Posts; User: sparkycivic

Page 1 of 5 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    10
    Views
    345

    Re: 4002i internal finisher weird problem

    Isn't the resting position of the new internal finisher tray *down*?
  2. [Error Code] Re: Task alfa CS-6002i S001 on U412 after installing maintenance kit

    platen glass underside, and scanner mirrors need to be clean for this to work.

    tap the lid button and observe the lamp... foggy glass?
    remove glass and use cellphone lamp near CCD, look down at...
  3. Replies
    9
    Views
    685

    [Electrical] Re: 8002i fax system 12 not recognized

    I had a fax stop working, but on a 306ci. it turned out to be the FFC that connects the main board to the expansion bay wasn't seated fully in the connector. this cable is the same across most of the...
  4. Replies
    2
    Views
    340

    Re: Add toner message

    Toner container drive gear/sprocket may have fallen apart. compare neighboring drives to look for missing parts.
  5. Re: TASKalfa 2551ci parts pipe transfer cleaning assy

    Yeah, it looks easy, but it's time consuming and that front plastic assembly is awkward to remove and install. If ONLY they put access holes for those two screws it would be unnecessary to remove the...
  6. Replies
    6
    Views
    752

    [Electrical] Re: Kyocera FS-C8020/8025 Power Supplies

    make sure to use the recent firmware, it changes the sleep behaviour so that main capacitors can't build-up excessive charge via power input spikes.
  7. Re: Kyocera Taskalfa 3252ci background and error codes

    are the waste exits of the drums or belt plugged? We have had a couple of pluggages of the waste conveying auger/chute near the waste bottle and a waste bottle not turning(deformed housing). They...
  8. Replies
    9
    Views
    850

    Re: M6526cdn with error C6000

    C2340 Fuser pressure release motor time-out error.
    "When the fuser pressure release motor is driven, the envelope switch (EVSW) is not detectable for 6s."

    Was that the correct fuser, and is it...
  9. Re: Kyocera Taskalfa 6550ci exit unit motor stalls

    the exit motor is likely stalling because the fuser exit signal wasn't received during the allowed time. the sensor is within the fuser...
  10. Replies
    20
    Views
    3,064

    [Misc] Re: Kyocera Setup Tool

    I always use the setup tool "convert" function. it does the whole batch of what's possible in one step.

    first, export ALL the 917 data to USB from old copier. Certain models won't convert unless...
  11. Replies
    2
    Views
    531

    Re: CS-2551ci C7620 and Magenta streaks

    the C7620 codes are symptomatic of toner being on the belt when none should be present. Any transfer cleaning issues will trigger C7620, but that code is never displayed to the user. Given the track...
  12. Replies
    12
    Views
    1,866

    [CQ] Re: TA-8002 belt run off

    Is the assembly sitting properly on in front of the spring loaded white buttons at the bottom, or on top? Maybe one of the buttons is stuck/busted?
    I always have a hard time getting that assembly to...
  13. Replies
    7
    Views
    2,294

    [Misc] Re: New TASKalfa 13600 Series aka RICOH

    KDAConnect is deprecated. Unfortunately, we must use KDA Central to get any new information or files. It's a terrible design, but it works.

    ... And the link for "production" equipment is Broken...
  14. Replies
    7
    Views
    1,865

    [Misc] Re: Kyocera Fleet Services

    which models are affected?
  15. Replies
    2
    Views
    1,593

    [Error Code] Re: Ram disk error

    1: update driver
    2: try spooler setting on/off
    3: try ram disk setting on/off combinations in driver and machine.
    That's my usual routine for this type of call
  16. Replies
    8
    Views
    1,188

    Re: TASKalfa 2551ci ticking cracking noise

    for all our 2550's and 2551's, creaking noises while preparing/post print is expected. Not sure where it comes from, but I suspect fuser or developer.
  17. Replies
    14
    Views
    3,848

    Re: DF-7120 J6511

    What was the setting before? Do you adjust these beyond default "0" values when installing or was it shipped that way?
  18. Replies
    5
    Views
    567

    Re: ECOYSYS 6525

    this particular model is particularly prone to this distortion issue.
    a modification exists that adds ramps to the path at the glass, but to be honest, adjusting the hinge height and also checking...
  19. Re: TASKalfa 3050Ci Service Mode Login not working

    Is Job Accounting turned on? Need to login first before svc mode will work.

    otherwise, maybe try starting copier with door open
  20. Replies
    11
    Views
    892

    Re: Kyocera fs 6525

    fs-6525 has no u906. "reset disabled unit" on models like this, is accomplished as per Black Cat's menu instructions.

    The finisher probably had a stapler jam or belt sensor error, and therefore...
  21. Replies
    2
    Views
    390

    [Electrical] Re: TaskAlfa 3252ci non responsive screen

    had one where some grit got between the bezel and the screen. try run a business card under the bezel all around, reboot copier. or disassemble the covers and inspect-if you're like that
  22. Thread: FS 6525

    by sparkycivic
    Replies
    2
    Views
    336

    Re: FS 6525

    is the 5v supply working? it Could have been waiting for a chance to die
  23. Replies
    8
    Views
    866

    Re: kfs frustrating lately

    what even is the point-of-contact for it? Usually web apps have a link to contact the dev team or similar, but I see none for KFS.
  24. Replies
    8
    Views
    866

    kfs frustrating lately

    Anybody else notice KFS having great difficulty the last few days with pulling reports, pulling maintenance mode info, or getting any info from machines?

    I've got several machines that I simply...
  25. Replies
    9
    Views
    1,380

    [CQ] Re: 2551ci transfer belt auger backing up

    schedule lots of time to tear apart the entire front and LHS of the machine for replacing that "parts pipe transfer cleaning assy".

    In hindsight of having done this a few times - a few...
Results 1 to 25 of 111
Page 1 of 5 1 2 3 4