Search:

Type: Posts; User: Horologydoc

Page 1 of 3 1 2 3

Search: Search took 0.14 seconds.

  1. Replies
    0
    Views
    317

    [Misc] 3 Tray Prescribe

    Hi guys,
    I have a customer that is looking to pull color paper from the bypass tray with no printing for page 1, letterhead printed on from tray 1 for page 2, bond printed on out of tray 2 for...
  2. Re: Kyocera taskalfa will not scan to folder on Windows 10

    Learned this one the hard way on a M3540. Go to the Control Panel > Programs and Features > Turn Windows Features On or Off on the left hand side. I'm attaching a screen shot of this menu. Scroll...
  3. Re: Printer Tray Selection Issue - Ricoh Aficio MP C3002

    You could also try changing the preferences in CUPS. It's a Unix based spooler new Mac OS use. There are plenty of videos and instructions if you google it.
  4. Replies
    10
    Views
    2,081

    [Misc] Re: Returning a leased Kyocera Copier

    My normal process is to make a copy of the return instructions/authorization and put a copy in the adf. I also print out a copy quality sample and leave that in the adf as well. Wrap the machine...
  5. Replies
    5
    Views
    2,638

    [Error Code] Re: Sharp MX3070N throwing H4-00 error

    The solution before this last firmware was to turn off the motion sensor energy save. Something you could also try.
  6. Replies
    2
    Views
    682

    [Dead] Re: kayocera km 4050

    Common issue. Doubt it is the firmware. Replace the operation tablet and then do U201.
  7. Thread: mx3610

    by Horologydoc
    Replies
    6
    Views
    1,610

    Re: mx3610

    Are you printing this on a heavy paper setting? If so print it on plain paper and check the image again. Haven't seen it on an Aries yet but, I remember having to adjust the motor velocity between...
  8. Replies
    13
    Views
    4,375

    Re: Ricoh Pro C901 SC670 Error

    Have you tried using a crossover from your laptop yet? The controller can cause 670 and 672 on Ricoh's as well. Remember you can't get into sc mode with a 670/672 but, you can get into 1993 and go...
  9. Replies
    3
    Views
    490

    Re: richo mp c6000 manual

    Make sure to clean and grease the bearings and gears on this model. Especially on the pressure roller. The MPC6000s have a bad habit of those rusting if you don't grease them properly. Just an fyi.
  10. Replies
    10
    Views
    1,284

    Re: MX-5141N 100lb Image Quality Issues

    Had a very similar issue on a MX5001 a few years back. Had to do basically the same thing you did and this Tech Tip helped me.
  11. Replies
    6
    Views
    1,897

    Re: mp9002 and sc670

    I know the SR 4030/40s had a board supplier change and there is 2 different firmwares. Did you load the correct finisher firmware?
  12. Replies
    11
    Views
    2,346

    Re: Sharp MX-B402SC information

    I have had what your are describing displayed when the HDD is going bad on these models. Could be as simple as re-flashing the firmware though.
  13. Replies
    7
    Views
    1,847

    Re: diference between MX230FU vs MX260FU

    You are right the 26/31 ppm have a longer shaft on the oil supply roller with a gear attached. Would be a quick way to tell the difference between the 23ppm and those.
  14. Replies
    3
    Views
    707

    Re: Ricoh Aficio 3045

    Login as supervisor then???
  15. Thread: MPC5502

    by Horologydoc
    Replies
    2
    Views
    2,242

    Re: MPC5502

    Just had this last week. Its your bcu and eeprom on the bcu. Replace them together and when you do you'll have to change 5807 to 2 for English in tech mode.

    21311
  16. Thread: MX7040

    by Horologydoc
    Replies
    7
    Views
    887

    Re: MX7040

    I had a sales rep sell one of these to a print shop. If they are going to be doing any cutting on bled images that they wanted backed up, run away as fast as you can. You can line it up fairly well...
  17. Re: How can i set to PDF when inbound routing for fax forward to email?

    You may also have to go into the address book and change the defaults that were saved when that folder was added.
  18. Replies
    2
    Views
    550

    Re: mpc 7500 light copies

    Make sure your firmware is 1.06:06 or newer. Check your sp3561 and make sure it's 8.5% or higher. If it is run image density correction under manual procon and then run full music. If it's below...
  19. Replies
    6
    Views
    1,088

    Re: MX5111N Toner Dusting w/new covers

    Just thought I'd mention to check IDNC in the next few weeks. Rumor has it that there will be firmware for this issue, on the virgos, being released soon.
  20. Replies
    11
    Views
    854

    [CQ] Re: Sharp MX-2700

    Are you cleaning up your follower rollers and transfer roller? If those are coated there is a noticeable difference in quality.
  21. Replies
    13
    Views
    3,000

    Re: Aficio MP C3500 - Intermittent SC681

    I've had the ribbon cable that runs underneath the board panel cause this sc code on this model before.
  22. Replies
    4
    Views
    529

    [Misc] Re: MPC 7501 advice/thoughts

    If they didn't grease the fuser gears when and if they maintenanced it (The rust is an indicator of this) I would definitely consider replacing at least the fuser gears with one ways and bushing...
  23. Thread: F1-00

    by Horologydoc
    Replies
    3
    Views
    1,693

    F1-00

    I've got a MX5110N with a MX-FN18 finisher and the MX-PNX6 punch that has been giving the customer a F1-00 code. I went out last week updated the firmware, checked the staple home position, checked...
  24. Replies
    3
    Views
    439

    Re: New style MP C4500 PCU's

    If you are referring to the B2242042 the answer is yes. Just have to remove the pin and shave the rear RJ45 like before. I haven't had any issues. Ricoh's official bulletin was that they changed...
  25. Replies
    15
    Views
    5,483

    Re: Ricoh MP 7502

    Check your lamp harnesses. They can cause 555 codes.
Results 1 to 25 of 52
Page 1 of 3 1 2 3