Search:

Type: Posts; User: repn1999

Page 1 of 10 1 2 3 4

Search: Search took 0.29 seconds.

  1. Replies
    23
    Views
    1,173

    Re: MX-4070 slow first copy

    IF this is an early 4070, that was put in the field before v4.01 firmware, replace the msata ssd. Sharp did not have TRIM enabled for the msata SSD prior to v4.01 and this caused WAYYY too much write...
  2. Replies
    13
    Views
    944

    [Misc] Re: Operation disabled

    I see issues like this with aries/aires II machine from time to time. We usually end up cloning the data if we can (address book, network settings) and the replace the sd card(with cards we make) and...
  3. Re: Sharp MX-5070N machine won't change Statatic IP

    ive seen strange issues like this when people clone all data from other families of machines. I have seen this once and had to wipe the hard drive replace the msata and program roms. I have also seen...
  4. Re: Sharp MX-2640N change fax transmission speed

    make sure ecm is turned off also.
  5. Re: Sharp MX-5001N slow printing on larg files (8mb +)

    Ive ran across this a couple times. Sometimes print as image helps. I recommend you use acrobat reader and not a browser to view pdfs. another thing to check is network speed. Sharp uses all pairs...
  6. Replies
    3
    Views
    140

    Re: Sharp MX-3570 Operation Panel blank

    was this a new LVDS board or one from Hytec? we had one that was bad from Hytec. Same symptom.
  7. Replies
    11
    Views
    1,008

    Re: mx-m565n Cleaning blade flip

    The trick is to use both the steric acid powder and yellow toner powder on both the drum and blade. If you refer to the tech bulletin about powders it points this out. Havenít had one flip once since...
  8. Replies
    5
    Views
    420

    Re: SHARP MX2614 - NO POWER!!

    Probably dc power supply. Could be sd card but only had that like once. 20 something other times was dc power supply
  9. Replies
    5
    Views
    436

    Re: MX-5070v high pitch noise

    replace the belt unit. there are other mods to that unit as well and its easier to get them all at once then make several calls when the other issues do finally come up. work smarter and not harder.
  10. Replies
    18
    Views
    1,654

    [Jamming] Re: MX-3640N Random jam & reeboot

    and i would also do 50-28 setup/adj all trays to confirm its not a timing issue after replacing the sensors
  11. Replies
    18
    Views
    1,654

    [Jamming] Re: MX-3640N Random jam & reeboot

    I have seen this issue before. One time it was the driver pwb being flaky and the other couple times it was the sensors in the vertical path both times in my case being the one before ppd2. I have I...
  12. Re: Turn off maintenance/PM-indication in the display.

    FYI you can skip doing pms to supposedly save money and sure you dont have to replace dv......BUT your toner life will drop to nothing and you will end up spending what you would have saved on the...
  13. Replies
    12
    Views
    760

    Re: MX4141 squeaking from web unit.

    I would suggest replacing all the bearings at rebuild and use krytox xht-s or gpl205 grease on them and all the gear shafts. never getting any noise problems unless its the web motor that needs...
  14. Replies
    16
    Views
    1,874

    Re: sharp mx 453 light prints and copies

    These machines seem to not make the pm cycles using aftermarket drums and toner...Sorry they just dont. First I would check the high voltage output and adjust it to what you get in SIM 8. Next I...
  15. Replies
    5
    Views
    657

    Re: MX5141 fuser wont stop running

    I was going to suggest thermistors. You can check the contact ones with a meter. I believe they should read 30 something ohms under normal just sitting condition. much more than that they are bad.
  16. Replies
    6
    Views
    976

    Re: New memory chips for the MX 4071

    I have been able to read the emmc card using a specific msata reader and external enclosure using raw copy. I have not had the chance to write one and see if it works because I dont have any...
  17. Replies
    2
    Views
    491

    Re: Sharp MX-3070 password changed

    I have had to reset these in the past without a DSK using the normal method of getting a code and contacting the hotline to get it reset. HOWEVER on other models I figured out that if you removed...
  18. Replies
    5
    Views
    481

    Re: Mx3110 vibrating noise

    did you use oem drums and mk kits? check the little gear on the back of the drum unit, and make sure the little tit is not broken on them. also check the transfer belt gear and drive gear to make...
  19. Re: Sharp MX-5070N machine won't change Statatic IP

    Did you guys do a full clone from a previous series machine to this one?
  20. Thread: Doc feeder

    by repn1999
    Replies
    7
    Views
    559

    [Misc] Re: Doc feeder

    would also be helpful to do 50-28 spf adjustment for both sides
  21. Thread: sharp mx-m465

    by repn1999
    Replies
    1
    Views
    265

    Re: sharp mx-m465

    you need to reinstall the watermark firmware using sim 49-3
  22. Thread: mx2640 f2-78

    by repn1999
    Replies
    5
    Views
    485

    [Error Code] Re: mx2640 f2-78

    I assume you stopped the machine and looked at the image on the belt before doing any more troubleshooting to see if the image is screwed up there. I am also assuming you have updated the firmware to...
  23. Replies
    7
    Views
    666

    Re: Sharp MX-2300n quality problem.

    I suspect that issue is from a cleaning blade not cleaning properly. It could be either the primary transfer belt blade or the drum blade for whatever color the latent or ghost image is. If you have...
  24. Thread: sharp mx-m465

    by repn1999
    Replies
    2
    Views
    360

    Re: sharp mx-m465

    reinstall the watermark firmware to resolve SIM 49-5. I have the firmware if you need it and cannot get it on your own.
  25. [Misc] Re: MX-4071 Duplex Paper Guide breaking when closing right door

    I would take a closer look at the delivery unit and ensure all is correctly assembled in that area as well as on the fuser. I believe part of the gate unit butts up against the fuser/delivery unit to...
Results 1 to 25 of 229
Page 1 of 10 1 2 3 4