Search:

Type: Posts; User: vigour

Page 1 of 20 1 2 3 4

Search: Search took 0.29 seconds.

  1. Thread: IR Adv C7065

    by vigour
    Replies
    8
    Views
    376

    [CQ] Re: IR Adv C7065

    Post a sample picture
  2. Replies
    2
    Views
    438

    [Misc] Re: Canon Tech Mobile

    You are correct.
    It will only work with Internet Explorer.
    I know the guys there, and I have complained about the issue. I was told told that it is not a priority at this time.
  3. Replies
    4
    Views
    517

    Re: Canon ir7086 v1 finisher e566-8001

    Do a search on the forum for E566. There is lots of info there.

    Check for a blown fuse on the MOTOR DRIVER
  4. Replies
    1
    Views
    185

    Re: RecommendedtFix-cln setting

    If you are running heavy coverage on the pages, and your web does not get tie to clean or lubricate properly
  5. Re: Canon IR5000 Feeding Issue on Duplex Legal Size only

    Replace reverse roller and outer delivery roller, they are worn down thin
  6. Replies
    10
    Views
    752

    [Misc] Re: Replacing Hard Disk of IR3300

    I used up to 20 gig drives on iR3300 many moons ago when they were in production.
    Then we would modify the system software
    Bigger drives would end up with missing functions
  7. Replies
    5
    Views
    542

    Re: Canon ir7086 v1 finisher problem

    you did not answer my other question.
    anyhow, check your fuse pcb for a blown fuse.
    check swing guide motor and sensor
  8. Replies
    5
    Views
    542

    Re: Canon ir7086 v1 finisher problem

    did you get any ecode
    Did you change the whole process unit or just the swing guide.
  9. Re: Thats me finished work.............retirement tomorrow.

    Buddy, all the best to you. ENJOY.
    I will tell you what everyone has been telling me . Keep busy
    I retired exactly a month ago, but I have not had the opportunity to craft a forum retirement post...
  10. Replies
    5
    Views
    396

    Re: Canon Advance c7055 error:000004-0801

    You took the power supply from a 9000.
    9000's run on 208 volts, The fuser lamp is also different from the 7000, so you should not swop fusers between 7000 and 9000
  11. Re: Remaining data that is not needed is been cleared.

    Why do you need help ?
    Your machine has extra security features installed.
    Do you want to get rid of them?
  12. Replies
    3
    Views
    319

    [Electrical] Re: canon ira 6065 sorter problem

    I would start by updating the system software.
    Possible mismatch
  13. Thread: IR-ADV-8285PRO

    by vigour
    Replies
    1
    Views
    232

    [Jamming] Re: IR-ADV-8285PRO

    Check the white plastic slider on the rear edge of the C!1 and C2 trays. Loosen the screw and slide them to the right. Tighten screw
  14. Replies
    5
    Views
    439

    Re: IR5055 DADF S1 roller turned to gummy bear

    I saw a tech pub on here long ago, where Canon would provide a new exchange feeder
    ...
  15. Replies
    1
    Views
    329

    [Error Code] Re: E 280-0001 Error Code on Canon ir adv 6065

    Last week I had this on a 7055.

    My scan lamp did not go on nor was there any movement of the scanner.
    I replaced the reader controller.
    You might get a different ecode after replacing the...
  16. [CQ] Re: EFI Color Calibration_ColorWise from Command WorkStation

    All the new Canon Fierys come with TIFFEN patches now
  17. Thread: Canon IR7105

    by vigour
    Replies
    8
    Views
    352

    Re: Canon IR7105

    That drum is ASI not OPC
  18. Replies
    6
    Views
    627

    Re: IRA C9075 PRO INIT-ITB giving "NG!"

    How to replace drum/itb driver.
    Remove back panel, and it will be right here below the flywheel

    The inner secondary roller and bearings may be seized. No part number for the bearings, so replace...
  19. Thread: e025 0402

    by vigour
    Replies
    4
    Views
    1,579

    Re: e025 0402

    Sounds like no toner is being added to the developer from the hopper
    Is there enough toner in the dev ?
    The dev may not be turning
  20. Replies
    14
    Views
    609

    Re: Canon irc PDF compact

    If you read the explanation you will see why NO ONE can give you what you are asking for
  21. Replies
    10
    Views
    611

    [Misc] Re: IRA6055 Lead edge dusting- Back ground

    There is a transfer roller in the ETB assembly, it goes bad sometimes
    The bearings seize up too.
    Sometimes you need to replace the whole assembly, modified ones have no springs to pinch when...
  22. Replies
    3
    Views
    497

    [Error Code] Re: iRA9070 - Multiple Error E007/E074/E013

    What voltage are you running that machine on. It should be 208volts
    The specs are written on the plug
    The C9065 and C9075 require 208VAC from a NEMA 6-15P outlet.

    Also check your lower fixing...
  23. Replies
    8
    Views
    688

    Re: Canon ir5570 duplex jamming

    What is your jam code
  24. Replies
    8
    Views
    688

    Re: Canon ir5570 duplex jamming

    Most likely you have a flat spot on your foam roller.
    Rotate it slowly an you should feel it.
    Replace foam roller
  25. Re: Revitailizing a formatted HD on a Canon 3245

    I think it should work if you just reload with SST
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4