Search:

Type: Posts; User: mntech

Page 1 of 8 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    2
    Views
    202

    [Error Code] Re: HP M631 stapler/stacker failure 66.80.17

    Thanks,
    After removing back panel, I spun the fan manually, heard am unusual rattle, removed fan and a tiny piece of black plastic fell from the fan motor, put it back together and it is now...
  2. Replies
    2
    Views
    202

    [Error Code] HP M631 stapler/stacker failure 66.80.17

    Hey guys

    Brand new LaserJet Enterprise MFP M631 was just setup, after 51 prints, machine threw 66.80.17 stapler stacker error. Can't print/copy at all.

    I don't see any obstructions at the...
  3. Replies
    2
    Views
    197

    Re: Need Toshiba es6540c exit sensor

    Thank you, I believe we found the part from one of our vendors.
    If for some reason I still need it, I'll send you a private message
  4. Replies
    2
    Views
    197

    Need Toshiba es6540c exit sensor

    Can anybody sell me an exit sensor for the e-studio 6540c

    Part nunber is: C0-15043000

    Thanks!
  5. Replies
    1
    Views
    249

    Need to buy es6540c exit sensor

    Can anybody sell me an exit sensor for the 6540c

    Part nunber is: C0-15043000

    I've already swapped it with fuser rotation sensor to verify it is bad, but am unable to find anywhere to purchase.
  6. Thread: jam E010 help

    by mntech
    Replies
    5
    Views
    962

    Re: jam E010 help

    Thanks for this post, I'm in the same boat, swapped sensors with the fuser sensor and problem followed the sensor.

    I can't find that sensor anywhere, and I'm not a Toshiba dealer.... Is there...
  7. Replies
    4
    Views
    317

    Re: Canon IR Adv C5045 broken transfer handle

    Awesome!

    Thanks! :D
  8. Replies
    4
    Views
    317

    Canon IR Adv C5045 broken transfer handle

    Customer broke the transfer belt unit release handle (They were attempting their own repairs), Is there a part number for JUST the handle? Or do i need to replaced the entire unit?

    I found an...
  9. Replies
    4
    Views
    650

    [CQ] Re: 356ci new machine, Magenta everywhere!

    Replacing the laser unit solved the problem.

    -mntech
  10. Re: Xerox Work Center 7556 going dead, or taking long to scan, stops mid print etc

    Sorry I wasn't clear on that, I typed that wrong....

    The actual Xerox part number for the fan includes the heatsink, but I also only just replace the fan with a generic 5 volt fan with a 3 pin...
  11. Re: Xerox Work Center 7556 going dead, or taking long to scan, stops mid print etc

    It's always the fan!

    I've replaced so many of these that i always keep a couple in my bag, we don't replace with stuck heatsink and fan, but a blast of air and a decent 5v 10mm fam does the...
  12. Replies
    10
    Views
    653

    Re: MP C3000 toner pump

    Thanks skinnyb! I had a similar experience earlier today;

    I pulled the IBT, the M and BK PCU units, taped the shutter open on the pump, and cheated the front door. Ran 5804 output check on the...
  13. Replies
    12
    Views
    993

    Re: Xerox counter reset

    Copiers are like cars, the odometers are there for a reason. I'm not sure if there are any laws against tampering with xerox meters, but i guarantee it is frowned upon in this community!
  14. Replies
    10
    Views
    653

    Re: MP C3000 toner pump

    New pumps. 1st time I just vacuumed the hose, second new pump I took the time to replace the hose. I did not reference vt (I can usually diagnose without). Also I can check and hear the pump clutch...
  15. Replies
    10
    Views
    653

    MP C3000 toner pump

    Have the infamous loading toner msg on black, replaced the pump, still wasn't loading, so replaced with another new pump..... Toner still not getting to dev unit.

    I've done dozens of these pumps...
  16. Replies
    11
    Views
    2,121

    Re: Clx-9201 stuck on boot screen

    Sorry, forgot to post update...

    I replaced just the OPE board and that fixed the machine

    Thanks
  17. Replies
    3
    Views
    667

    Re: E-Studio 5540C with C3B0 and C390

    I didn't see any diagonal voids or even light areas on any of the mag rollers, or on the transfer belt patches themselves. I was doing single color sky shots and although the machine would fault out...
  18. Replies
    1
    Views
    615

    Oki MPS 3537 firmware

    Does anyone have access to the firmware for this machine? Trying to resolve an F101 error

    Also, are all these hard drives those special Wipe Technology drives or can they be either.

    Thanks,...
  19. Replies
    4
    Views
    650

    [CQ] Re: 356ci new machine, Magenta everywhere!

    There were codes for failed registration (can't remember exact code) but I assumed this was due to the high coverage of magenta.

    I'll double check connections at laser and engine.
  20. Replies
    3
    Views
    667

    E-Studio 5540C with C3B0 and C390

    Hey,

    Get called out for a CE40 on a es5540c, first thing customer tells me is that the machine may have water damage, after a leaky ceiling....

    I ran thru the procedure in the manual for CE40,...
  21. Replies
    4
    Views
    650

    [CQ] 356ci new machine, Magenta everywhere!

    Hey all,
    I have a new 356ci that has less than 200 on the meter, machine ran fine during testing and after delivery, but a week or so later, customer calls about magenta on the whole page. I swapped...
  22. Replies
    3
    Views
    2,570

    Re: Kyocera Net Gateway Administrator Password

    So I mixed those up, here is the correct logins:

    For java based gateway:
    Login: Admin
    Pass: Admin#1234
    *note both login and pass has to be a capital 'A'

    .Net based gateway
    Login:...
  23. Replies
    8
    Views
    643

    Re: HP Color LJ 3600 faint blacks

    Fixed.

    The cam lever that contacts the cartridges to engage/disengage contact between the mag roller and drum was slightly out of place.

    Must have been bumped when re-install the drive...
  24. Replies
    11
    Views
    2,121

    Clx-9201 stuck on boot screen

    Samsung multixpress clx-9201 is stuck on boot screen, never make it past the Samsung logo, the "thinking" icon spins a couple times then freezes

    I can access syncthru, but I don't see anywhere to...
  25. Replies
    8
    Views
    643

    Re: HP Color LJ 3600 faint blacks

    Contacts are secure and making good contact with both the hv board and the drum unit
Results 1 to 25 of 198
Page 1 of 8 1 2 3 4