Results 1 to 9 of 9
  1. #1
    Senior Tech 250+ Posts
    Join Date
    Feb 2014
    Location
    Bristol
    Posts
    456
    Rep Power
    26

    MX2314 - please wait

    I've read the posts on this error posted earlier in this forum but some relate to the 2614 and not the basic 2314. The ram is onboard and not a plug in dimm.

    My machine boots up fine, cleans the transfer belt message comes and goes then it calibrates itself all ok and then says please wait and just sits there. No restart or anything works, can't access system settings or service mode. You can ping it and get a reply but can't open machines webpage.

    Tried emergency firmware update which all went through fine but problem exactly the same?


    Sent from my iPhone using Tapatalk

  2. #2
    Senior member of CRS 2,500+ Posts
    MX2314 - please wait

    ZOOTECH's Avatar
    Join Date
    Jul 2007
    Location
    Insane Diego, CA
    Posts
    3,367
    Rep Power
    102

    Re: MX2314 - please wait

    Quote Originally Posted by Leebs14 View Post
    I've read the posts on this error posted earlier in this forum but some relate to the 2614 and not the basic 2314. The ram is onboard and not a plug in dimm.

    My machine boots up fine, cleans the transfer belt message comes and goes then it calibrates itself all ok and then says please wait and just sits there. No restart or anything works, can't access system settings or service mode. You can ping it and get a reply but can't open machines webpage.

    Tried emergency firmware update which all went through fine but problem exactly the same?


    Sent from my iPhone using Tapatalk
    Unplug the network cable and see if it goes ready.
    "You can't trust your eyes, if your mind is out of focus" --

  3. #3
    Senior Tech 250+ Posts
    Join Date
    Feb 2014
    Location
    Bristol
    Posts
    456
    Rep Power
    26

    Re: MX2314 - please wait

    No it doesn't. I unplugged it from the network and then did the firmware but it's exactly the same..


    Sent from my iPhone using Tapatalk

  4. #4
    Senior member of CRS 2,500+ Posts
    MX2314 - please wait

    ZOOTECH's Avatar
    Join Date
    Jul 2007
    Location
    Insane Diego, CA
    Posts
    3,367
    Rep Power
    102

    Re: MX2314 - please wait

    Disable Warmup in TC 7-1 to see if it will go ready; also, disable Fusing and DV to see if it will go ready.
    Run TC 25-1 (with toners removed) and check for any levels that might be near over toned or under toned.
    "You can't trust your eyes, if your mind is out of focus" --

  5. #5
    Senior Tech 250+ Posts
    Join Date
    Feb 2014
    Location
    Bristol
    Posts
    456
    Rep Power
    26

    Re: MX2314 - please wait

    Thanks for your suggestions but the machine will not allow you into any modes at all to adjust or turn anything on or off. Even starting the machine with the door open it still won't accept p*c* code


    Sent from my iPhone using Tapatalk

  6. #6
    Senior Tech 250+ Posts
    Join Date
    Feb 2014
    Location
    Bristol
    Posts
    456
    Rep Power
    26

    Re: MX2314 - please wait

    Update - been back today a replaced the SD card and it worked first time. So must have been corrupted data on the card,


    Sent from my iPhone using Tapatalk

  7. #7
    Field Tech 500+ Posts
    MX2314 - please wait

    michaelc's Avatar
    Join Date
    Mar 2011
    Location
    England
    Posts
    590
    Rep Power
    37

    Re: MX2314 - please wait

    It happens on a few sharps. I keep an image of each SD on my laptop for this. Happy you fixed.
    It didn't say that I couldn't do it in the manual.

  8. #8
    Junior Member
    Join Date
    Dec 2016
    Posts
    3
    Rep Power
    0

    Re: MX2314 - please wait

    Quote Originally Posted by michaelc View Post
    It happens on a few sharps. I keep an image of each SD on my laptop for this. Happy you fixed.
    Hi dear,
    you can send me a copy of your sd card?
    I have a printer sharp mx2314, it has blocked the sd and I can not start it.


    I'm waiting.
    Thank you

  9. #9
    Junior Member
    Join Date
    Jun 2022
    Location
    Dubai
    Posts
    1
    Rep Power
    0

    Re: MX2314 - please wait

    Quote Originally Posted by michaelc View Post
    It happens on a few sharps. I keep an image of each SD on my laptop for this. Happy you fixed.
    Can you pls share the sd card image for mx2314n

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here