Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 9 of 9
  1. #1
    mammm23
    Guest

    L4-02 in Sharp ARM-450

    Hi, I have the error code L4-02 in a Sharp ARM-450. I executed the sim 25-1 as the service manual indicates and the drum motor works fine. Any suggestions to remove this error???


  2. #2
    OMD-227
    Guest
    Drum Motor Lock. Seen this many, many times.
    Remove the process unit, remove the drum & check the waste toner auger & gear assy. You will probably find this is seized or broken due to excessive drum cleaning. When changing the drum & developer, you must reset the rotation counters as well as the drum/dev counters. Otherwise, there is excessive over-toning, leading to waste toner filling the toner cartridge waste area too quickly & therefore leading to waste toner auger assy blocking up.
    You will probably need a new process unit as the auger drive gear breaks off the frame.
    There is new firmware for this problem. Make sure it is updated. Once this is done, it will not happen again. Trust me..... seen it way too many times. All firmware updated machines run perfectly. The rotation counters need to be reset to prevent the overtoning in the first place.


  3. #3
    mammm23
    Guest
    Hi,
    Do you know which is the correct version of Firmware??
    where can I find it??
    What is the process to upgrade it??

    Thanks a lot for help


  4. #4
    Trusted Tech 50+ Posts
    Join Date
    Jul 2008
    Posts
    94
    Rep Power
    20
    01.05.05 Tiger Firmware O00.zip

    Main - mJ.10; Boot - m5.03A; PCU - 9.04; Scn - 06.04) firmware AR-M350/M450/M350U/M450U/M350N/M450N.

    Sim 22-05 Definition of version ROM and serial number of the device

    Firmware series AR-M350 and AR-M450 it is updated through parallel port
    The device by means of the Parallel cable (Centronics) and programs
    FCOPY.EXE

    Note: Update the first Boot Rom, then Main Rom.
    Procedure is connected with switching (jp) of crosspieces on a payment

    Has forgotten to tell, that
    1. Update Firmware - process not idle time. You do it at own risk.
    2. Try before Update Firmware, to keep an old file.
    3. Version O00.zip - for Russia but English language is present.
    Answered here are absolutely right.
    I had a case. After maintenance service. The clearing edge was turned out also the same result. At what the copy was absolutely normal.

    Attached Files Attached Files
    Last edited by vlad_; 07-31-2008 at 08:08 AM.

  5. #5
    Master Of The Obvious 10,000+ Posts
    L4-02 in Sharp ARM-450

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    15,404
    Rep Power
    249
    Wazza is right. Start there. Most often it's a locked up cleaning unit causing it.

    But there is one other possibility. On a few occasions I've had the HVT cables shorting to the main drive assembly. I imagine you coud try to order separate HVT cables, but I've always just replaced the main drive assembly. It's a major pain to change. If it's your first time it will take you over an hour to get the thing out and on the floor. The main drive assy is good for ~1M copies before it starts to seize. If you're getting close to that don't hesitate to replace the assy. =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

  6. #6
    Junior Member
    Join Date
    Jan 2013
    Location
    Sioux City, IA.
    Posts
    3
    Rep Power
    0

    Re: L4-02 in Sharp ARM-450

    I also have had to replace Main Drive to fix The L4-02--Good Luck


  7. #7
    Legendary Frost Spec Tech 2,500+ Posts
    L4-02 in Sharp ARM-450

    Akitu's Avatar
    Join Date
    Oct 2010
    Location
    Thompson, MB
    Posts
    2,607
    Rep Power
    85

    Re: L4-02 in Sharp ARM-450

    Quote Originally Posted by SCtech View Post
    I also have had to replace Main Drive to fix The L4-02--Good Luck
    4 year necro-bump!

    Cthulhu for president! Why settle for the lesser evil?

  8. #8
    Trusted Tech 50+ Posts Arcadian's Avatar
    Join Date
    Feb 2010
    Posts
    63
    Rep Power
    16

    Talking Re: L4-02 in Sharp ARM-450

    I just changed the PCU unit, and problem solved, but you'll need to vacuum the machine I would rather take it outside and give it a grand old air dry cleaning job.


  9. #9
    Senior Tech 250+ Posts
    L4-02 in Sharp ARM-450


    Join Date
    Oct 2008
    Location
    Manchester, NH
    Posts
    404
    Rep Power
    23

    Re: L4-02 in Sharp ARM-450

    The above are all correct, but I have corrected several by replacing DV Drive spring, per bulletin MFP-TB-290. If your DV ever spilled and it is piled up behind the machine around the Main drive unit, I would think it is safe to say that you will need a drive unit.

    As far as broken waste toner gear on process unit, I have only replaced the 3 gears on the back and not the whole process unit.



Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here